www.fmiproducts.com
56131L
21
VENTING INSTALLATION
Continued
Number
Description
PA58-712 Adjustable 7"-12" Section Double
Wall Pipe, Galvanized
FPA58-6 6" Dura Vent Collar to FMI Pipe
Adaptor
E58-45
45° Elbow, Galvanized
E58-90
90° Elbow, Galvanized
FSE58-45 45° Starter Elbow (Dura Vent to
FMI Pipe)
FP-58
Firestop Plate
WF-58
Wall Firestop, Galvanized
RF-58-6 Roof Flashing - 0 to 6/12 Pitch,
Galvanized
RF-58-12 Roof Flashing - 6/12 to 12/12 Pitch,
Galvanized
S-58
Vinyl Siding Standoff, Galvanized
VT-58
Vertical Round Termination, Gal-
vanized
HHT-58 High Wind Round Horizontal Ter
-
mination Kit, Galvanized
HTS-58 Horizontal Square Termination,
Galvanized
HHTK-58 High Wind Round Horizontal
Termination Kit (Includes Round
Termination, Wall Firestop, 45°
Elbow)
ST-58-14 14" Snorkel Termination, Galva-
nized
ST-58-36 36" Snorkel Termination, Galva-
nized
SF-58
Stucco Flashing - For use with
HTS-58
VR-58
Vertical Restrictor, Galvanized
WS-58
Wall Strap
SC-58
Storm Collar, Galvanized
CS-58
Cathedral Ceiling Support
PARTS LIST FOR FMI VENTING KITS AND COMPONENTS
FMI (5"/8") Pipe & Vent Kits
Number
Description
VKR-58 Roof Vent Kit, Galvanized
(Includes: 45° Elbow, 7"-12"
Adjustable Pipe, Flue Restrictor,
Vertical High Wind Termination, 2'
Pipe, 4' Pipe, Wall Firestop, Storm
Collar, Roof Flashing [0/12 - 6/12],
26 Screws)
VKB-58 Basement Vent Kit, Galvanized
(Includes: 45° Elbow, 7"-12"
Adjustable Pipe, Wall Firestop,
Horizontal Square Termination, 4'
Pipe, 90° Elbow, 20 Screws)
VKS-58 Snorkel Vent Kit, Galvanized
(Includes: 45° Elbow, 7"-12" Ad-
justable Pipe, Wall Firestop, 36"
Snorkel Termination, 4' Pipe, 1'
Pipe, 90° Elbow, 26 Screws)
VKG-58 Ground Floor Vent Kit, Galva-
nized (Includes: 45° Elbow, 7"-12"
Adjustable Pipe, Wall Firestop,
Horizontal Square Termination, 16
Screws)
P58-48 48" Section Double Wall Pipe,
Galvanized
P58-36 36" Section Double Wall Pipe,
Galvanized
P58-24 24" Section Double Wall Pipe,
Galvanized
P58-12 12" Section Double Wall Pipe,
Galvanized
P58-6
6" Section Double Wall Pipe, Gal-
vanized
HIGH ALTITUDE INSTALLATION
Your FMI PRODUCTS, LLC direct-vent
fireplace has been tested and approved for
elevations from 0-2,000 feet (USA).
Fireplaces for High Altitude (models ending
in -HA) are for installation above 4,000 feet
only. These fireplaces are equipped with parts
specific for higher altitudes.
IMPORTANT:
These fireplaces can NOT be converted to
propane/LP gas.
When installing a non-high altitude fireplace at
an elevation above 2,000 feet (USA), you may
need to decrease the input rating by changing
the existing burner orifice to a smaller size.
Reduce input 4% for each 1,000 feet above
sea level. Check with your local gas company
for proper orifice size identification.
IMPORTANT:
For horizontal installations
above 2,000 feet, it is recommened that a
12" extension pipe be added before starter
elbow (see Figure 33, page 20).
