background image

UNVENTED (VENT-FREE)

NATURAL GAS LOG HEATER

ALSO DESIGN-CERTIFIED AS A VENTED DECORATIVE APPLIANCE

OWNER’S OPERATION AND INSTALLATION MANUAL

®

Patent Pending

Save this manual for future reference.

18", 24" and 30" Variable

Manually-Controlled Models

This appliance may be installed in an aftermarket* manufactured (mobile) home, where not prohib-
ited by state or local codes.

* Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer

Heat Majic™

Models FVF18N,

FVF24N, and

FVF30N

WARNING: If the information in this
manual is not followed exactly, a fire or
explosion may result causing property
damage, personal injury, or loss of life.

— Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
— WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do

not use any phone in your building.

• Immediately call your gas supplier

from a neighbor’s phone. Follow the
gas supplier’s instructions.

• If you cannot reach your gas sup-

plier, call the fire department.

— Installation and service must be
performed by a qualified installer, ser-
vice agency, or the gas supplier.

WARNING: Improper installation, ad-
justment, alteration, service, or mainte-
nance can cause injury or property dam-
age. Refer to this manual for correct
installation and operational procedures.
For assistance or additional informa-
tion consult a qualified installer, ser-
vice agency, or the gas supplier.

WARNING: This appliance is for instal-
lation only in a solid-fuel burning ma-
sonry  or UL127 factory-built fireplace,
or in an approved ventless firebox. It is
design certified for these installations
in accordance with ANS Z21.11.2. Ex-
ception: Do not install this appliance in
a factory-built fireplace that includes
instructions stating it has not been
tested or should not be used with
unvented gas logs.

WARNING: This is an unvented gas-fired heater. It uses air (oxygen) from the room in
which it is installed. Provisions for adequate combustion and ventilation air must be
provided. Refer to 

Air for Combustion and Ventilation section on page 4 of this manual.

Содержание Heat Majic FVF18N

























Отзывы: