FMI EzC18N Скачать руководство пользователя

Страница: 5 / 32

www.fmiproducts.com

125010-01A

PRODUCT IDENTIFICATION

Figure 1 - Product Identification

Ignitor

UNPACkING

Log Set

LOCAL CODES

VULC24NR/PR Shown

Control Knob

Install and use heater with care. Follow all

local codes. In the absence of local codes,

use the latest edition of

The National Fuel

Gas Code, ANSI Z223.1/NFPA 54

*Available from:

American National Standards Institute, Inc.

1430 Broadway

New York, NY 10018

National Fire Protection Association, Inc.

Batterymarch Park

Quincy, MA 02269

State of Massachusetts: The installation

must be made by a licensed plumber

or gas fitter in the Commonwealth of

Massachusetts.
Sellers of unvented propane or natural

gas-fired supplemental room heaters shall

provide to each purchaser a copy of 527

CMR 30 upon sale of the unit.
Vent-free gas products are prohibited for

bedroom and bathroom installation in the

Commonwealth of Massachusetts.

CAUTION: Do not remove data

plates from grate assembly. Data

plates contain important war-

ranty and safety information.

1. Remove logs and heater base assembly

from carton.

Note: Do not pick up heater base assem-

bly by burners. This could damage heater.

Always handle base assembly by grate.

2. Remove all protective packaging applied

to logs and heater for shipment.

3. Check heater for any shipping damage. If

heater is damaged call FMI PRODUCTS,

LLC at 1-866-328-4537 for replacement

parts before returning to dealer.

PRODUCT FEATURES

OPERATION

This heater is clean burning. It requires no

outside venting. There is no heat loss out a

vent or up a chimney. Heat is generated by

both realistic flames and glowing coals. This

heater is designed for vent-free operation with

flue damper closed. It has been tested and

approved to ANSI Z21.11.2 standard for un-

vented heaters. State and local codes in some

areas prohibit the use of vent-free heaters.

This heater may also be operated as a vented

decorative (ANSI Z21.60) product by opening

the flue damper.

SAFETY DEVICE

This heater has a pilot with an Oxygen Deple-

tion Sensing (ODS) safety shutoff system. The

ODS/pilot is a required feature for vent-free

room heaters. The ODS/pilot shuts off the

heater if there is not enough fresh air.

ELECTRONIC IGNITION SYSTEM

This heater has an electronic ignitor to light

pilot.

Содержание EzC18N

































Результаты поиска

Содержание EzC18N

Отзывы:

Похожие инструкции для EzC18N

Бренды по названию

Популярные бренды

FMI EzC18N, Руководство владельца по эксплуатации и установке

Результаты поиска

Содержание EzC18N

Отзывы:

Похожие инструкции для EzC18N

Бренды по названию

Популярные бренды