background image

www.fmiproducts.com

125010-01A

25

SPECIFICATIONS

VULC18PV, EZC18P

•  Rating (Variable): 19,000/26,000 Btu/Hr

•  Type Gas: Propane/LP

•  Ignition: Electronic

•  Manifold Pressure: 7.9" W.C.

•  Inlet Gas Pressure (in. of water):

  Max - 14" W.C., Min - 11" W.C*.

VULC18NV, EZC18N

•  Rating (Variable): 22,000/29,000 Btu/Hr

•  Type Gas: Natural

•  Ignition: Electronic

•  Manifold Pressure: 3.4" W.C.

•  Inlet Gas Pressure (in. of water):

  Max - 10.5" W.C., Min - 5" W.C.*

VULC24PV, VULC30PV, EZC24P, 

EZC30P

•  Rating (Variable): 24,000/35,000 Btu/Hr

•  Type Gas: Propane/LP

•  Ignition: Electronic

•  Manifold Pressure: 7.9" W.C.

•  Inlet Gas Pressure (in. of water):

  Max - 14" W.C., Min - 11" W.C.*

VULC24NV, VULC30NV, EZC24N, 

EZC30N

•  Rating (Variable): 24,000/35,000 Btu/Hr

•  Type Gas: Natural

•  Ignition: Electronic

•  Manifold Pressure: 3.4" W.C.

•  Inlet Gas Pressure (in. of water):

  Max - 10.5" W.C., Min - 5" W.C.*

*For purpose of input adjustment

REPLACEMENT PARTS

Note:  Use  only  original  replacement  parts. 

This will protect your warranty coverage for 

parts replaced under warranty.

Contact authorized dealers of this product. 

If  they  can’t  supply  original  replacement 

part(s),  call  FMI  PRODUCTS,  LLC.  at 

1-866-328-4537.

When calling, have ready
•  your name
•  your address
•  model and serial numbers of your heater
•  how heater was malfunctioning
• 

type of gas used (propane/LP or natural gas)

•  purchase date
Usually, we will ask you to return the part to 

the factory.

SERVICE HINTS

When Gas Pressure Is Too Low

•  pilot will not stay lit
•  burners will have delayed ignition
•  heater will not produce specified heat
•  propane/LP gas supply may be low

You may feel your gas pressure is too low. If 

so, contact your local propane/LP or natural 

gas supplier.

TECHNICAL SERVICE

You  may  have  further  questions  about 

installation,  operation  or  troubleshooting. 

If  so,  contact  FMI  PRODUCTS,  LLC  at 

1-866-328-4537. When calling please have 

your  model  and  serial  numbers  of  your 

heater ready.
You can also visit our web site at

www.fmiproducts.com

.

Содержание EzC18N

































Отзывы: