background image

www.fmiproducts.com

125206-01B

13

VENTING INSTALLATION

 WARNING: This gas fireplace 

and  vent  assembly  must  be 

vented directly to the outside. The 

venting system must NEVER be 

attached to a chimney serving a 

separate solid fuel burning appli

-

ance. Each gas appliance must 

use a separate vent system. Do 

not use common vent systems.

 WARNING: Horizontal sec-

tions of this vent system require 

a minimum clearance of 2" from 

the top of the pipe and 1" mini

-

mum to the sides and bottom. 

Vertical sections of this system 

require a minimum of 1" clear

-

ance  to  combustible  materials 

on all sides of the pipe.

INSTALLATION PLANNING

There are two basic types of direct-vent 

installation:

•  Horizontal Termination
•  Vertical Termination

It is important to select the proper length 

of vent pipe for the type of termination you 

choose. It is also important to note the wall 

thickness.

For Horizontal Termination:

 Select the 

amount of vertical rise desired. The horizontal 

run of venting must have 1/4" rise for every 

12" of run towards the termination.

 WARNING: Never run the 

vent downward as this may 

cause  excessive  temperatures 

which could cause a fire.

You may use one or two 90° elbows in this 

vent configuration. See 

Horizontal Termina-

tion Configurations

 on page 17.

For Vertical Termination: 

Measure distance 

from fireplace flue outlet to ceiling. Add ceiling 

thickness, vertical rise in an attic or second 

story, and allow for sufficient vent height 

above roof line. You may use one or two 90° 

elbows in this vent configuration. See 

Vertical 

Termination Configurations

 on page 20.

 WARNING: Read all instruc-

tions completely and thoroughly 

before  attempting  installation. 

Failure to do so could result in 

serious injury, property damage 

or loss of life.

NOTICE: Failure to follow these in-

structions will void the warranty.

NOTICE: Do not seal termination 

cap to vent pipe. Cap must be 

removable  for  vent  inspection 

and maintenance.

INSTALLATION PRECAUTIONS

Consult local building codes before beginning 

installation. The installer must make sure to 

select the proper vent system for installa-

tion. Before installing vent kit, the installer 

must read this fireplace manual and vent kit 

instructions.

Only a qualified service person should install 

venting system. The installer must follow 

these safety rules:

•  Wear gloves and safety glasses for pro

-

tection

•  Use extreme caution when using ladders 

or when on roof tops

•  Be aware of electrical wiring locations in 

walls and ceilings

The following actions will void the warranty 

on your venting system:

•  Installation of any damaged venting com

-

ponent

•  Unauthorized  modification  of  the  venting 

system

•  Installation of any component part not manu

-

factured or approved by FMI PRODUCTS, 

LLC 

•  Installation  other  than  as  instructed  by 

these instructions

f i r e - p a r t s . c o m

Содержание DVF32TMHPN-LS





































Отзывы: