FMI DVF-36LT-D Скачать руководство пользователя

Страница: 24 / 40

www.fmiproducts.com

125079-01F

FIREPLACE INSTALLATION

Continued

REPLACING BATTERIES IN HAND-

HELD REMOTE CONTROL AND AC

BATTERY BACKUP

Replacing Batteries in AC Battery

Backup

1.  Remove bottom access door.
2.  Remove battery pack from metal housing.
3.  Remove  existing  batteries.  Install  4  AA

batteries into battery pack following posi

tive and negative directions.

4. Insert battery pack back into metal hous

ing.

5. Replace bottom access door.

Installing Batteries in Remote Control

Unit

1. Remove battery cover on back of remote

control unit.

2. Remove battery.
3. Install 1 A23/12V battery following positive

and negative directions.

4. Replace battery cover onto remote control unit.

Figure 32 - Connecting/Disconnecting

Gas Line to Millivolt Valve

Equipment

Shutoff

Valve

Millivolt

Control

Valve

Flexible Gas

Line, Do NOT

Kink

To Gas Supply

(Natural)

To External

Regulator

(Propane/LP)

Figure 33 - Removing/Installing Burner Base

CONNECTING AND DISCONNECTING

GAS LINE

WARNING: A qualified ser

vice person must connect and

disconnect fireplace with gas

supply. Follow all local codes.

1. Using a 5/16" hex socket wrench or nut-

driver, connect or disconnect flexible gas

line and control valve (see Figure 32).

2. After connecting gas line to control valve,

always test for leaks.

REMOVING LOG SET/BURNER MODULE

WARNING: Never use an open

flame to check for a leak. Apply

noncorrosive leak detection fluid

to joints. Bubbles forming show

a leak. Correct leaks at once.

CAUTION: The gas supply

shall be shut off prior to discon

necting the electrical power, if

any, before proceeding with this

installation.

CAUTION: Use gloves when

removing the log set/burner mod

ule from your firebox. Some metal

edges may be sharp. Use caution

with log sets as logs are fragile.

1. Remove glass door (see page 21).

2. Remove grate and all floor media (see

page 22).

3. Carefully lift and remove 3 hearth refrac

tories from fireplace.

4. Remove 3 spacers from firebox bottom

(see Figure 33).

5. For 36" models only:

Remove 3 loose

logs from log set (see Figure 28, 28a and

28b, page 22).

6. Remove 9 screws from front and sides of

firebox burner base. Lift entire base from

unit by pulling forward to disengage from rear

flange and then lifting up (see Figure 33).

7. If needed, replace burner gasket before

reinstalling log set/burner module (see

replacement parts list on page 38.)

Log

Assembly

Firebox

Bottom

Burner Base

Screws

Spacers

Содержание DVF-36LT-D









































Результаты поиска

Содержание DVF-36LT-D

Отзывы:

Похожие инструкции для DVF-36LT-D

Бренды по названию

Популярные бренды

FMI DVF-36LT-D, Руководство владельца по эксплуатации и установке

Результаты поиска

Содержание DVF-36LT-D

Отзывы:

Похожие инструкции для DVF-36LT-D

Бренды по названию

Популярные бренды