2
13. Do not tilt lawnmower when the motor is running, except
when starting and stopping. In this case, do not tilt more
than absolutely necessary and lift only the part which is
away from the operator. Always ensure that both hands
are in the operating position before returning the appli-
ance to the ground.
14. Do not put hands near the grass discharge chute.
15. Never pick up or carry a mower when it is operating
or still connected to the mains supply.
16. Remove the plug from the mains :
-
before leaving the mower unattended for any period;
-
before clearing a blockage;
-
before checking, cleaning or working on the appliance;
-
if you hit an object. Do not use your lawnmower
until you are sure that the entire lawnmower is in a
safe operating condition.;
-
if the lawnmower starts to vibrate abnormally. Check
immediately. Excessive vibration can cause injury
Maintenance and storage
1. Keep all nuts, bolts and screws tight to be sure the
lawnmower is in safe working condition.
2. Check the grassbox frequently for wear or deterioration.
3. Replace worn or damaged parts for safety.
4. Only use the replacement blade, blade bolt, spacer
and impeller specified for this product.
5. Be careful during adjustment of the lawnmower to
prevent entrapment of the fingers between moving
blades and fixed parts of the machine.
CABLES
IMPORTANT
•
Use only 1.00mm
2
size cable up to 30 metres length
maximum for trimmers and 60 metres length maxi-
mum for lawnmowers.
Maximum rating :
1.00mm
2
size cable, 10 amps 250 volts AC.
•
YOUR LAWNMOWER IS SUPPLIED WITH AN ELEC-
TRIC MAINS CABLE FITTED WITH A FEMALE CON-
NECTOR.
1. Flymo Mains Cables and Extension Cables are avail-
able from your local Electrolux Outdoor Products
Approved Service Centre.
2. Do not wire an extension cable directly to your prod-
uct yourself. Please contact your local Electrolux
Outdoor Products Approved Service Centre for fur-
ther information on the connectors and kits available.
3. Only use extension cables specifically designed for
outdoor use.
CONNECTORS
IMPORTANT
•
Flymo connectors are suitable for use with 2 core
cable only. Under no circumstances should these
connectors be used for earthed products.
•
All Flymo connectors and cables are of splashproof con-
struction. They are not waterproof and must not be left
outside permanently nor should they be submerged or
immersed in water. Do not let cable lay or trail through
pools of water or splashed with water from hose pipes.
MAINS PLUG REPLACEMENT
IMPORTANT
• If the plug supplied is cut off it should be destroyed.
There is an electric shock hazard if a cut off plug is
inserted into a 13 amp socket.
1.
No earth required.
Flymo products are double insu-
lated to EN60335 and under no circumstances
should an earth be connected to any part of the
product.
2.
Ensure the mains voltage suits your product
3.
IMPORTANT!
The wires in the mains lead are coloured in accor-
dance with the following code:
BLUE - NEUTRAL
BROWN - LIVE
The wire which is coloured BLUE must be connected
to the Terminal which is marked with the letter 'N' or
coloured BLACK.
The wire which is coloured BROWN must be con-
nected to the Terminal which is marked with the letter
'L' or coloured RED.
4. It is important that the outer sheath is clamped cor-
rectly into the 3-pin plug.
5. If in doubt consult your local Service Repairer or qual-
ified electrician before the machine is used.
6.
A 13 Amp fuse must be fitted to the Mains Plug.
7. The normal plug fuse and household fuse only pro-
tect the electrical equipment and are not a safeguard
against electrocution.
E
L
F
U
S
E
N
BLACK
OR
BLUE
RED
OR
BROWN
Lower Handles - Venturer 370 (B1, B2)
1. Locate 2 screws into the holes in the handles.
2. Using a pozidrive screwdriver, secure the screws into
the lower handles, ensuring the point of the screw
stays inside the handle.
(B1)
3. Insert lower handles, with screws attached, into the
deck and fully tighten screws.
(B2)
Note: The screw will form its own thread
Wheel Assembly (if not already fitted)
A1
A2
If wheels are not already fitted:-
1. Select one of the holes in the mounting plate and
note it as the other wheels will need to be adjusted to
the same position.
(A1)
2. Locate the fixing bolt through hole in the hub cap,
wheel and selected hole in mounting plate.
3. Turn the wheel hub in a clockwise direction until the
wheel assembly is securely located to the deck.
(A2)
Lower Handle Assembly - Venturer 370
B1
B2
ensure
the point
of the
screw
stays
inside
the han-
dle
