Flymo EasiLife GO Скачать руководство пользователя страница 43

Страница: 43 / 48

Mowing

EasiLife GO

Cutting system

3 pivoted cutting blades

Cutting motor speed, rpm

2670

Power consumption during cutting, W +/- 20 %

Cutting height, cm / in.

2-4.5 / 0.8-1.8

Cutting width, cm / in.

16 / 6.3

Narrowest possible passage, cm / in.

60 / 24

Maximum slope for cutting area, %

Maximum slope for boundary wire, %

Maximum length boundary wire, m / ft.

300 / 980

Maximum length guide loop

, m / ft.

150 / 490

IP-classification

EasiLife GO

Product

IPX5

Charging station

IPX5

Power supply

IP44

Bluetooth

EasiLife GO

Operating frequency band, MHz

2400 - 2484

Maximum transmitted power, dBm

Husqvarna AB does not guarantee full compatibility between the product and other types of wireless systems such as

remote controls, radio transmitters, hearing loops, underground electric animal fencing or similar.
The products are made in England or the Czech Republic. See information on the rating plate. Refer to

Introduction

on page 3

8.2 Registered trademarks

The

Bluetooth

word mark and logos are registered trademarks owned by

Bluetooth SIG, inc.

and any use of such

marks by Flymo is under license.

The guide loop is the loop that if formed by the guide wire and the part of the boundary wire from the junction

with the guide wire to the right connection in the charging station.

1622 - 001 - 03.03.2021

Technical data - 43

Содержание EasiLife GO

















































Результаты поиска

Содержание EasiLife GO

Отзывы:

Похожие инструкции для EasiLife GO

Бренды по названию

Популярные бренды

Flymo EasiLife GO, Руководство оператора

Результаты поиска

Содержание EasiLife GO

Отзывы:

Похожие инструкции для EasiLife GO

Бренды по названию

Популярные бренды