Flymo EasiLife GO Скачать руководство пользователя страница 41

Страница: 41 / 48

7 Transportation, storage and disposal

7.1 Transportation

The supplied Li-ion batteries obey the Dangerous Goods

Legislation requirements.
•

Obey all applicable national regulations.

•

Obey the special requirement on package and

labels for commercial transportations, including by

third parties and forwarding agents.

7.2 Storage

•

Fully charge the product. Refer to

To charge the

battery on page 25

•

Switch off the product. Refer to

To switch off the

product on page 25

•

Clean the product. Refer to

Clean the product on

page 27

•

Keep the product in a dry, frost free space.

•

Keep the product with all wheels on level ground

during storage.

•

If you keep the charging station indoors,

disconnect and remove the power supply and all

the connectors from the charging station. Put the

end of each connector wire in a connector

protection box.

Note:

If you keep the charging station outdoors,

do not disconnect the power supply and the

connectors.

•

Speak to your Flymo service for information about

available storage accessories for your product.

7.3 Disposal

•

Obey the local recycling requirements and

applicable regulations.

•

For questions about how to remove the battery,

refer to

Battery on page 29

1622 - 001 - 03.03.2021

Transportation, storage and

disposal - 41

Содержание EasiLife GO

















































Результаты поиска

Содержание EasiLife GO

Отзывы:

Похожие инструкции для EasiLife GO

Бренды по названию

Популярные бренды

Flymo EasiLife GO, Руководство оператора

Результаты поиска

Содержание EasiLife GO

Отзывы:

Похожие инструкции для EasiLife GO

Бренды по названию

Популярные бренды