7
To stop:
1. Release the start lever
(16)
.
The trimmer stops.
2. Push the locking button
(A)
and remove the battery
(B)
from the battery
holder
(D)
.
Trimmer line extension (automatic) [ Fig. O15 ]:
A clean cut is achieved only with the maximum trimmer line
(13)
length.
The trimmer line
(13)
is lengthened automatically when the spool comes to
a standstill after switch off.
As the trimmer line can only be lengthened in small increments, it can
be necessary in some cases to repeat the switch-off / switch-on action
several times (up to 6 times). Important is that the spool comes to
a complete standstill each time.
The trimmer line
(13)
has been sufficiently lengthened when, after switch-on,
it audibly strikes the line limiter
(17)
.
The FLYMO Spool and line Art. FLY098 / 535670090 or the FLYMO Trim-
mer line Art. NLO012 / 577616312 have to be replaced when the trimmer
line has been used up.
4. MAINTENANCE
DANGER! Risk of injury!
Cut injury when the product starts accidentally.
v
Wait for the trimmer line to stop and remove the battery
before you maintain the product.
To clean the trimmer [ Fig. M1 ]:
DANGER! Risk of injury!
Risk of injury and risk of damage to the product.
v
Do not clean the product with water or with a water jet
(in particular high-pressure water jet).
v
Do not clean with chemicals including petrol or solvents.
Some can destroy critical plastic parts.
The airflow slots must always be clean.
1. Clean the airflow slots
(17)
with a soft brush (do not use a screwdriver).
2. Clean all movable parts after each operation. Especially remove any
grass and dirt from the protective cover
(12)
.
3. Remove the wheel
(10)
by pressing one of the buttons
(19)
to clean it.
To replace the spool and line [ Fig. M2 ]:
DANGER! Risk of injury!
Do not use metallic cutting elements or replacement parts and
accessories not provided by FLYMO.
Only use original FLYMO Spool and line. You can order Replace-
ment Spool and line from your FLYMO dealer or directly from the
FLYMO Customer Service.
• FLYMO Spool and line
Art. FLY098 / 535670090
1. Release the spool cover
(20)
by pressing both locking clips
(21)
and
remove the cover.
2. Remove the spool
(22)
.
3. Clean the automatic lever
(23)
. The automatic lever
(23)
must move freely.
4. Feed the trimmer line
(13)
of the new spool
(22)
through the hole
(24)
and
pull out about 10 cm.
5. Insert the spool
(22)
. Do not trap the trimmer line
(13)
when you do this.
6. Fit the spool cover
(20)
so that both locking clips
(21)
audibly engage.
v
If the spool cover
(20)
cannot be touched down, turn the spool
(22)
to and
fro, until the spool
(22)
is completely in the spool holder.
The trimmer may only be used when the spool cover
(22)
is
engaged.
To replace the trimmer line [ Fig. M3 ]:
Only use original FLYMO Trimmer Line. You can order the replace-
ment Trimmer line from your FLYMO dealer or directly from the
FLYMO Customer Service.
• FLYMO Trimmer line
Art. NLO012 / 577616312
1. Remove the spool
(22)
(see 4. MAINTENANCE To replace the spool
and line).
2. Remove the rest of the trimmer line
(13)
.
3. Clean the spool
(22)
and the automatic lever. The automatic lever must
move freely.
4. Take approximately 8 m of the new trimmer line and insert 15 mm of
the trimmer line
(13)
into the hole in the spool
(22)
.
5. Wind the trimmer line
(13)
in the direction of the arrows on the top of the
spool
(22)
. Make sure that the trimmer line
(13)
is neatly coiled on the
spool. (Failure to do so will impair the efficiency of the automatic trim-
mer line extension.)
6. Leave approximately 10 cm of the trimmer line unwound and push it
into the cleat
(24)
.
7. Insert the spool again (see 4. MAINTENANCE To replace the spool
and line).
To clean the battery and the battery charger:
Make sure that the surface and the contacts of the battery and the
battery charger always are clean and dry before you connect the battery
charger.
Do not use running water.
v
Battery charger: Clean the contacts and the plastic parts with a soft
and dry cloth.
v
Battery: Occasionally clean the ventilation slots and the terminals on
the battery using a soft brush that is clean and dry.
5. STORAGE
To put into storage:
The product must be stored away from children.
1. Remove the battery.
2. Charge the battery.
3. Clean the trimmer, the battery and the battery charger
(see 4. MAINTENANCE).
4. Store the trimmer, the battery and the battery charger in a dry,
enclosed and frost-free place.
Disposal:
(in accordance with RL2012/19/EC / S.I. 2013 No. 3113)
The product must not be disposed of to normal household
waste. It must be disposed of in line with local environmental
regulations.
IMPORTANT!
v
Dispose of the product through or via your municipal recycling
collection centre.
Disposal of the battery:
Li-ion
The FLYMO battery contains lithium-ion cells that should not be
disposed of with normal household waste at the end of its life.
IMPORTANT!
v
Dispose of the batteries through or via your municipal recycling
collection centre.
1. Discharge the lithium-ion cells completely (contact the FLYMO Service).
2. Protect the contacts on the lithium-ion cells against short circuits.
3. Dispose of the lithium-ion cells properly.
6. TROUBLESHOOTING
DANGER! Risk of injury!
Cut injury when the product starts accidentally.
v
Wait for the trimmer line to stop and remove the battery
before you troubleshoot the product.
To pull the trimmer line out of the spool manually [ Fig. T1 ]:
A trimmer line
(13)
that is too short or no longer extends automatically when
the trimmer is turned on can be pulled out manually.
v
Hold down the automatic lever
(23)
and pull the trimmer line
(13)
at the
same time.
42260-85.960.01.indd 7
42260-85.960.01.indd 7
12.10.21 11:36
12.10.21 11:36
