8
To release retracted or welded trimmer line:
If the trimmer line
(13)
has disappeared into the spool
(22)
or if the automatic
trimmer line extension still doesn’t work after pulling the trimmer line
(13)
it
may be welded in the spool
(22)
.
1. Remove the spool
(22)
(see 4. MAINTENANCE To replace the trimmer
line).
2. Unwind the trimmer line
(13)
.
3. Clean the spool
(22)
, the automatic lever
(23)
and the trimmer line
(13)
.
The automatic lever
(23)
must move freely.
4. Wind the trimmer line
(13)
onto the spool
(22)
again
(see 4. MAINTENANCE To replace the trimmer line).
5. Insert the spool
(22)
again (see 4. MAINTENANCE
To replace the spool).
Problem
Possible Cause
Remedy
Trimmer does not cut
Trimmer line is worn or too
short.
v
Extend the trimmer line.
Trimmer line is empty.
v
Replace the spool or the
trimmer line.
Trimmer line is pulled into the
spool or welded.
v
Pull the trimmer line out of
the spool.
Trimmer line cannot be
extended or is used quickly
Trimmer line became too
dry and brittle (e. g. during
the winter).
v
Put the spool in water for
approx. 10 hours.
Trimmer line frequently
touched hard objects.
v
Prevent the trimmer line from
touching hard objects.
Automatic lever is dirty.
v
Clean the automatic lever.
Continuous clattering noise
Too much trimmer line was
fed out.
v
Wind the trimmer line onto
the spool.
Trimmer line limiter is missing.
v
Contact the FLYMO Service.
Wheel stops turning
Wheel is dirty.
v
Clean the wheel.
Trimmer can no longer
be stopped
Start lever is stuck.
v
Remove the battery and
loosen the start lever.
Trimmer does not start
or stops.
LED
(L1)
is flashing green
[ Fig. O4 ]
Battery is empty.
v
Charge the battery.
Trimmer does not start
or stops.
Error-LED
(Wp)
is illuminated
red [ Fig. O4 ]
Battery temperature is outside
the permissible temperature
range.
v
Wait until the battery tem
perature is between
0 °C – + 45 °C again.
There are drops of water or
moisture between the battery
contacts on the trimmer.
v
Remove the water drops /
moisture with a dry cloth.
Engine is blocked.
v
Remove the obstacle.
Start again.
Trimmer does not start
or stops.
Error-LED
(Wp)
is flashing
red [ Fig. O4 ]
Product is defective.
v
Contact the FLYMO Service.
Trimmer does not start
or stops.
Error-LED
(Wp)
is not
illuminated [ Fig. O4 ]
Battery is not put completely
into the battery holder.
v
Put the battery completely
into the battery holder until
it audibly engages.
Battery is defective.
v
Replace the battery.
Product is defective.
v
Contact the FLYMO Service.
Charging is not possible.
Battery charge indicator
(Lc)
is continuously illuminated
[ Fig. O3 ]
The battery is not connected
(correctly).
v
Connect the battery to
charger correctly.
Battery contacts are dirty.
v
Clean the battery contacts
(e. g. by connecting and
disconnecting the battery
several times. Replace the
battery if necessary.
Battery temperature is outside
the permissible charging
temperature range.
v
Wait until the battery
tem perature is between
0 °C – + 45 °C again.
Battery is defective.
v
Replace the battery.
Battery charge indicator
(Lc)
is not illuminated [ Fig. O3 ]
Mains plug of the charger is
not (correctly) plugged in.
v
Insert the mains plug into the
mains socket (completely).
Battery charge indicator
(Lc)
is not illuminated [ Fig. O3 ]
Socket outlet, mains cable or
charger is defective.
v
Check the mains voltage.
Let the charger be checked
if necessary by an authorised
specialist dealer or the
FLYMO Service.
For any other malfunctions please contact the Husqvarna UK Ltd. Customer
Service. Repairs must only be done by Husqvarna UK Ltd. service departments
or specialist dealers approved by FLYMO.
7. TECHNICAL DATA
Battery Trimmer
Unit
Value
(Art. 9705445-xx / 9705447-xx)
Cutting width
cm
26
Rpm of spool
R/min.
8400
Trimmer line diameter
mm
1.6
Trimmer line supply
m
8
Trimmer line feed
automatic
Weight (without Battery)
kg
2.5
Sound pressure level L
pA
1)
Uncertainty k
pA
dB (A)
77
3
Sound power level L
WA
2)
:
measured / guaranteed
Uncertainty k
WA
dB (A)
89 / 91
2
Hand / arm vibration a
vhw
1)
Uncertainty k
vhw
m/s
2
3
1.5
Measuring process complying with:
1)
EN 50636291
2)
RL 2000/14/EC / S.I. 2001 No.1701
NOTE: The stated vibration emission value has been measured according to
a standardized test procedure and can be used for comparison of one electric
power tool with another. It can also be used for preliminary evaluation of expo-
sure. The vibration emission value can vary during actual use of the electric power tool.
System Battery
Unit
Value (Art. 531382601)
PBA 18V 2.5Ah W-B
Battery voltage
V (DC)
18
Battery capacity
Ah
2.5
Number of cells (Li-Ion)
5
Appropriate POWER FOR ALL system Battery Chargers:
AL 1810 CV / AL 1815 CV / AL 1830 CV / AL 1880 CV.
Battery Charger
AL 1810 CV P4A
Unit
Value (Art. 531382201)
Mains voltage
V (AC)
220 – 240
Mains frequency
Hz
50 – 60
Rated power
W
26
Battery charging voltage
V (DC)
18
Max. battery charging
current
mA
1000
Battery charging time 80 % /
97 – 100 % (approx.)
PBA 18V 2.0Ah W-B
PBA 18V 2.5Ah W-B
PBA 18V 4.0Ah W-C
min.
min.
min.
96 / 124
120 / 154
192 / 244
Permitted charging
temperature range
°C
0 – 45
Weight according to
EPTA-Procedure 01:2014
kg
0.17
Protection class
/ II
Appropriate POWER FOR ALL system Batteries: PBA 18V.
8. ACCESSORIES
FLYMO Spool and line
As replacement for consumed spool and line.
Art. FLY098 /
535670090
FLYMO Trimmer line
As replacement for consumed line.
Art. NLO012 /
577616312
FLYMO System Battery
PBA 18V/45 P4A
PBA 18V/72 P4A
Battery for additional duration or
for replacement.
Art. 531382601
Art. 531382701
FLYMO Battery Charger
AL 1810 CV P4A
Charger for the POWER FOR ALL system
Batteries PBA 18V..W..
Art. 531382201
9. SERVICE / WARRANTY
Service:
Please contact the address on the back page.
42260-85.960.01.indd 8
42260-85.960.01.indd 8
12.10.21 11:36
12.10.21 11:36
