Flying Voice FGW4148-16S Скачать руководство пользователя страница 42

Страница: 42 / 78

Chapter 4 Web Interface

FGW4148-16S/32S/48S User Manual

Local Service

Gateway will not forward DHCP packets between LAN and WAN, it also blocks

DHCP packets from the WAN port. Clients connected to the LAN port can get IP
from DHCP server run in gateway.

VLAN Mode

Disable

The WAN interface is untagged. LAN is untagged.

Enable

The WAN interface is tagged. LAN is untagged.

Trunk

Only valid in bridge mode. All ports, including WAN and LAN, belong to this VLAN
Id and all ports are tagged with this VLAN id. Tagged packets can pass through
WAN and LAN.

VLAN ID

Set the VLAN ID.

802.1p

Set the priority of VLAN, Options are 0~7.

Note

Multiple WAN connections may be created with the same VLAN ID

Содержание FGW4148-16S















































































Результаты поиска

Содержание FGW4148-16S

Отзывы:

Похожие инструкции для FGW4148-16S

Бренды по названию

Популярные бренды

Flying Voice FGW4148-16S, Руководство пользователя

Результаты поиска

Содержание FGW4148-16S

Отзывы:

Похожие инструкции для FGW4148-16S

Бренды по названию

Популярные бренды