Flying Voice FGW4148-16S Скачать руководство пользователя страница 17

Страница: 17 / 78

Chapter 1 Product description

FGW4148-16S/32S/48S User Manual

Hardware Installation

Before configuring your router, please see the procedure below for instructions on connecting the device in
your network.

Procedure 1 Configuring the Router

Connect analog phone to ATA Port with an RJ11 cable.

Connect the WAN port to the Interne your network

’

s modem/switch/router/ADSL

equipment using an Ethernet cable.

Connect one end of the power cord to the power port of the device. Connect the other end to the
wall outlet.

Check the Power, WAN, and LAN LED to confirm network connectivity.

Ground

Connect the ground wire

Fan

For equipment cooling

AC 100~220V

Connector for a power adapter.

Warning

Please do not attempt to use unsupported power adapters and do not remove power during
configuring or updating the device. Using other power adapters may damage

FGW4148-16S/32S/48S and will void the manufacturer warranty.

Содержание FGW4148-16S















































































Результаты поиска

Содержание FGW4148-16S

Отзывы:

Похожие инструкции для FGW4148-16S

Бренды по названию

Популярные бренды

Flying Voice FGW4148-16S, Руководство пользователя

Результаты поиска

Содержание FGW4148-16S

Отзывы:

Похожие инструкции для FGW4148-16S

Бренды по названию

Популярные бренды