Fluke ScopeMeter 123 Скачать руководство пользователя страница 60

Страница: 60 / 96

Fluke 123/124/125

Service Manual

3-30

PAL310.BMP

Figure 3-13. Test Tool Screen for PAL/SECAM

line 310

NTSC262.BMP

Figure 3-14. Test Tool Screen for NTSC line 262

Apply the inverted TV Signal Generator signal to the test tool.
You can invert the signal by using a Banana Plug to BNC adapter (Fluke PM9081/001)
and a Banana Jack to BNC adapters (Fluke PM9082/001), as shown in Figure 3-15.

ST8142.WMF

Figure 3-15. Test Tool Input A to TV Signal Generator Inverted

Select the following test tool setup:

•

Fluke 123/124: press

to open the SCOPE INPUTS menu.

•

Fluke 123/124: press

to open the TRIGGER menu and choose:

VIDEO on A

The VIDEO TRIGGER sub-menu is shown now. From the VIDEO TRIGGER
menu choose:

SYSTEM:

NTSC

PAL

SECAM

PALplus |

LINE:

SELECT | POLARITY:

NEGATIVE

•

Fluke 125: press

to open MENU.

Содержание ScopeMeter 123

































































































Результаты поиска

Содержание ScopeMeter 123

Отзывы:

Fluke ScopeMeter 123, Руководство по обслуживанию, Страница: 60 / 96

Результаты поиска

Содержание ScopeMeter 123

Отзывы: