Fluke ScopeMeter 123 Скачать руководство пользователя страница 41

Страница: 41 / 96

Performance Verification

3.5 Input A and Input B Tests

3-11

•

Fluke 123/124: press

to open the TRIGGER menu, and choose:

INPUT:

B | SCREEN UPDATE:

FREE RUN | AUTO RANGE:

>15Hz

•

Fluke 125: press

to open MENU.

•

Fluke 125: press

to open the TRIGGER menu, and choose :

INPUT:

B | UPDATE:

FREE RUN | AUTO RANGE:

>15Hz

Set the 5500A to source a leveled sine wave of 600 mV peak-to-peak (SCOPE output,
MODE levsine). Set the 5500A to Operate (OPR).

Set the 5500A frequency according to the first test point in Table 3-1.

Observe the Input B main reading on the test tool and check to see if it is within the
range shown under the appropriate column.

Continue through the test points.

When you are finished, set the 5500A to Standby.

3.5.6 Input B Frequency Response Upper Transition Point Test

Proceed as follows to test the Input B frequency response upper transition point:

Connect the test tool to the 5500A as for the previous test (see Figure 3-4).

Select the following test tool setup:

•

Turn Input B on (if not already on).

•

Press

to select auto ranging (

AUTO

in top of display).

Do not press

anymore!

•

Using

change the sensitivity to select manual sensitivity ranging, and lock

the Input B sensitivity on 200 mV/div.

•

Fluke 123/124: press

to open the SCOPE INPUTS menu.

•

Fluke 123/124: press

to open the TRIGGER menu, and choose:

INPUT:

B | SCREEN UPDATE:

FREE RUN | AUTO RANGE:

>15Hz

•

Fluke 125: press

to open MENU.

•

Fluke 125: press

to open the TRIGGER menu, and choose :

INPUT:

B | UPDATE:

FREE RUN | AUTO RANGE:

>15Hz

Set the 5500A to source a leveled sine wave of 1.2V peak-to-peak, 50 kHz (SCOPE
output, MODE levsine). Set the 5500Ato Operate (OPR).

Adjust the amplitude of the sine wave to 6 divisions on the test tool display.

Set the 5500A to 20 MHz (Fluke 123) or 40 MHz (Fluke 124/125), without changing the
amplitude.

Observe the Input B trace check to see if it is

≥

4.2 divisions.

When you are finished, set the 5500A to Standby.

Содержание ScopeMeter 123

































































































Результаты поиска

Содержание ScopeMeter 123

Отзывы:

Fluke ScopeMeter 123, Руководство по обслуживанию, Страница: 41 / 96

Результаты поиска

Содержание ScopeMeter 123

Отзывы: