manualshive.com logo in svg

Fluke ScopeMeter 123, Руководство по обслуживанию, Страница: 53 / 96

Поделиться
Скачать
Fluke ScopeMeter 123 Скачать руководство пользователя страница 53

 

Performance Verification

 

 

3.5 Input A and Input B Tests

 

3

 

  

3-23 

 

ST8129.WMF 

Figure 3-8. Test Tool Input A-B to 5500A Normal Output for >300V 

2.

 

Select the following test tool setup: 

•

 

Press 

 to select auto ranging (

AUTO

 in top of display).   

Do not press 

 anymore! 

•

 

Press 

 to open the INPUT A MEASUREMENTS menu, and choose:  

 

MEASURE on A: 

 Vac 

•

 

Press 

 to open the INPUT A MEASUREMENTS menu, and choose:  

 

MEASURE on A: 

 Vdc 

(Vdc becomes main reading, Vac secondary reading)

 

•

 

Press 

 to open the INPUT B MEASUREMENTS menu, and choose: 

 INPUT 

B: 

 ON | MEASURE on B: 

 Vac 

•

 

Press 

 to open the INPUT B MEASUREMENTS menu, and choose: 

 INPUT 

B: 

 ON | MEASURE on B: 

 Vdc 

•

 

Move the Input A and Input B ground level (indicated by zero icon 

 ) to the center 

grid line. Proceed as follows: 

⇒

 

Press 

 to enable the arrow keys for moving the Input A ground level. 

⇒

 

Press 

 to enable the arrow keys for moving the Input B ground level. 

⇒

 

Using the 

 keys move the ground level. 

3.

 

Using 

 set the Input A and B sensitivity to the first test point in Table 3-7. 

The corresponding range is shown in the second column of the table. 

4.

 

Set the 5500A to source the required AC voltage (NORMAL output, WAVE sine). Set 
the 5500A to Operate (OPR). 

5.

 

Observe the Input A and B main reading (V-dc) and secondary reading (V-ac) and check 
to see if it is within the range shown under the appropriate column. 

6.

 

Continue through the test points. 

Содержание ScopeMeter 123

































































































Отзывы:

Нет отзывов