Fluke BT21ANG Скачать руководство пользователя страница 35

Страница: 35 / 66

Use the Product

Make Measurements

3-9

View Test Readings on the Screen

This is a typical display of battery test in Meter mode.

hsz028.jpg

This is a typical display of battery test in Sequence mode:

hsz031.jpg

Battery number:

Indicates the number of the battery that has been tested.

Progress bar:

The progress bar is generated according to the total number of batteries

in the profile. Each cell corresponds to one battery. An empty cell indicates the

corresponding battery is not tested yet. A full cell indicates the corresponding battery has

been tested and the readings have been saved. A cross mark in a full cell indicates that

the threshold function is enabled.

Cursors:

Use



and



to move the cursors. The number of the currently tested battery

changes accordingly. When the cursors are positioned on a full cell, the corresponding

reading of that battery will be shown under the progress bar.

Average readings:

After two or more sets of test readings are saved, the Product

shows the average readings, including average resistance and average voltage.
Tip: If the test readings of a battery are significantly different from the average readings,

it could indicate the battery health has been compromised.

1.888.610.7664

[email protected]

Fluke-Direct

.com

Содержание BT21ANG



































































Результаты поиска

Содержание BT21ANG

Отзывы:

Бренды по названию

Популярные бренды

Fluke BT21ANG, Руководство пользователя

Результаты поиска

Содержание BT21ANG

Отзывы:

Бренды по названию

Популярные бренды