background image

LIMITED WARRANTY AND LIMITATION OF LIABILITY

Each Fluke product is warranted to be free from defects in material and workmanship under normal use and 

service. The warranty period is three years and begins on the date of shipment. Parts, product repairs, and 

services are warranted for 90 days. This warranty extends only to the original buyer or end-user customer of a 

Fluke authorized reseller, and does not apply to fuses, disposable batteries, or to any product which, in Fluke's 

opinion, has been misused, altered, neglected, contaminated, or damaged by accident or abnormal conditions of 

operation or handling. Fluke warrants that software will operate substantially in accordance with its functional 

specifications for 90 days and that it has been properly recorded on non-defective media. Fluke does not warrant 

that software will be error free or operate without interruption.
Fluke authorized resellers shall extend this warranty on new and unused products to end-user customers only but 

have no authority to extend a greater or different warranty on behalf of Fluke. Warranty support is available only if 

product is purchased through a Fluke authorized sales outlet or Buyer has paid the applicable international price. 

Fluke reserves the right to invoice Buyer for importation costs of repair/replacement parts when product purchased 

in one country is submitted for repair in another country.
Fluke's warranty obligation is limited, at Fluke's option, to refund of the purchase price, free of charge repair, or 

replacement of a defective product which is returned to a Fluke authorized service center within the warranty 

period.
To obtain warranty service, contact your nearest Fluke authorized service center to obtain return authorization 

information, then send the product to that service center, with a description of the difficulty, postage and insurance 

prepaid (FOB Destination). Fluke assumes no risk for damage in transit. Following warranty repair, the product will 

be returned to Buyer, transportation prepaid (FOB Destination). If Fluke determines that failure was caused by 

neglect, misuse, contamination, alteration, accident, or abnormal condition of operation or handling, including 

overvoltage failures caused by use outside the product’s specified rating, or normal wear and tear of mechanical 

components, Fluke will provide an estimate of repair costs and obtain authorization before commencing the work. 

Following repair, the product will be returned to the Buyer transportation prepaid and the Buyer will be billed for the 

repair and return transportation charges (FOB Shipping Point).
THIS WARRANTY IS BUYER'S SOLE AND EXCLUSIVE REMEDY AND IS IN LIEU OF ALL OTHER 

WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF 

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. FLUKE SHALL NOT BE LIABLE FOR ANY 

SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSSES, INCLUDING LOSS OF 

DATA, ARISING FROM ANY CAUSE OR THEORY.
Since some countries or states do not allow limitation of the term of an implied warranty, or exclusion or limitation 

of incidental or consequential damages, the limitations and exclusions of this warranty may not apply to every 

buyer. If any provision of this Warranty is held invalid or unenforceable by a court or other decision-maker of 

competent jurisdiction, such holding will not affect the validity or enforceability of any other provision.

11/99

Fluke Corporation
P.O. Box 9090
Everett, WA 98206-9090
U.S.A.

Fluke Europe B.V.
P.O. Box 1186
5602 BD Eindhoven
The Netherlands

Содержание 729 Pro



























































Отзывы: