manualshive.com logo in svg

Fluke 6100B, Начало работы

Поделиться
Скачать
Fluke 6100B Скачать руководство пользователя страница 13

 

Electrical Power Standards 

 

General Safety Summary 

5 

W

Caution  

To avoid damage to the Instrument, take into account direct 

sunlight, radiators and other heat sources when assessing the 

ambient temperature. 

Fuse Requirements 

The Instruments require a special fuse with rated current of 15 A and rated breaking 

capacity of 750 A. The fuse must be rated for a voltage of 250 V ac. 
To access the fuse and ensure the line power is disconnected, follow the procedure 

described in the Users Manual. The approved fuse is shown below. 

Fluke part number and description: 

1998159 

T15AH 250 V 32 mm 

Fuse manufacturer and part number:  

Bussmann 

MDA-15 

Measurement Category I 

Measurement terminals are designed for connection at Measurement (Overvoltage) 

Category I.  

XW

Warning 

To avoid electrical shock, personal injury, or fire hazard, do not 
connect the Instrument's terminals directly to the ac line power 
supply or any other source of voltage or current that might 
temporarily exceed the peak ratings of the Instrument. 

Maintenance and Repair 

Always observe local or national safety regulations and rules for the prevention of 

accidents and hazard while performing any work. Always disconnect the Instrument from 

all signal sources and then the ac line power supply before removing any covers. Any 

adjustment, parts replacement, maintenance or repair should be carried out only by Fluke 

authorized technical personnel. 

XW

Warning 

To avoid electrical shock, personal injury, or fire hazard, it is 
essential that only manufacturer supplied parts be used to 
replace parts relevant to safety. Safety tests must be performed 
after the replacement of parts relevant to safety. 

Cleaning 

Ensure the Instrument signal and then power leads are disconnected prior to cleaning. 

Use only a damp, lint-free cloth to clean fascia and case parts. See the Users Manual for 

details of air filter cleaning. 

Ventilation and Dust 

The Instrument relies on forced-air cooling via ventilation slots in the sides of the 

Instrument. Adequate ventilation can usually be achieved by positioning the Instrument 

on a level surface and by leaving a 100 mm (4 in gap) around the Instrument. Care should 

be taken to avoid restricting the airflow at the sides of the Instrument, as damage may 

result from overheating. The Instrument is designed to IP4X and is specified for use in a 

Pollution Category 2 environment, which is normally non–conductive with temporary 

light condensation.  

W

Caution 

To avoid damage to the Instrument, do not use in dusty, damp, 

or wet conditions. 

Содержание 6100B



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды