manualshive.com logo in svg

Fluke Calibration P5515, Руководство пользователя

Поделиться
Скачать
Fluke Calibration P5515 Скачать руководство пользователя страница 16

P5515, P5515-V, & P5515-EP 

Users Manual 

8 

Note 

During this operation, bubbles may appear in the reservoir, as trapped air 
is expelled. For large volumes, repeat steps 3 &.4 until no further bubbles 
appear. 

5.

 

With valve open, turn capstan fully out and close valve. The tester is now ready for 

use. 

W

 Warning 

Turning the capstan out with the reservoir valve closed will 
generate approximately 15 inHg / 0.5 bar vacuum. If the DUT is 
vacuum sensitive, leave valve open during priming operation. 

Operation 

1.

 

Turn the screw press in (clockwise) to generate pressure. 

Note 

The priming pump is intended for system priming only, and cannot be used 
to generate high pressures. 

2.

 

Allow a few moments for the system to stabilize before taking any readings, 

especially after large changes in system pressure. 

Note 

Large, sudden changes in pressure will cause the system temperature to 
rise or fall, which can cause instrument readings to change as the fluid in 
the system expands or contracts, thus increasing or decreasing the 
pressure. 

3.

 

Compare the reading of the gauge under test with that of the master gauge. 

4.

 

For the next, higher calibration point, repeat from step 1 above. 

5.

 

To measure reducing pressures, turn the screw press out (counter-clockwise). 

6.

 

Depressurize the system by turning the screw press FULLY OUT, then open the 

reservoir valve— 

W

 Caution 

Never release the system pressure by using the reservoir valve 

alone, as sudden depressurization will “shock” the system, 

which may cause damage to sensitive instruments attached 

to it. 

Maintenance and Servicing 

The figures on the following pages detail the components of each assembly, together with 

the relevant part numbers. Where “SPEC” appears as a part number, this indicates that 

this particular component varies with the specification of the comparison test pump, and 

is usually associated with other components in an assembly for replacement purposes. 

The part number for the seal kit for the P5515, P5515-V, and P5515-EP is P5515SK, 

P5515SK-V, and P5515SK-EP, respectively

.

 

Top Plate Removal 

1.

 

Depressurize the system, open the reservoir valve, and turn the screw press fully in. 

2.

 

Disconnect any DUT from the test ports, and drain the fluid from the system; the 

reservoir is fitted with a drain plug, which can be accessed from the underside of the 

instrument, see Chapter 5, Reserve Assembly. 

Содержание P5515





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды