manualshive.com logo in svg

Fluke Calibration P5515, Руководство пользователя

Поделиться
Скачать
Fluke Calibration P5515 Скачать руководство пользователя страница 10

P5515, P5515-V, & P5515-EP 

Users Manual 

2 

Safety Information 

Safety Summary 

The following are general safety precautions that are not related to any specific 

procedures and do not appear elsewhere in this publication. These are recommended 

precautions that personnel must understand and apply during equipment operation and 

maintenance to ensure safety and health and protection of property. 

W

 Warning 

If the equipment is used in a manner not specified by the 
manufacturer, the protection provided by the equipment may be 
impaired. 

Compressed Liquid 

Use of compressed liquids can create an environment of propelled foreign matter.   

Pressure system safety precautions apply to all ranges of pressure. Care must be taken 

during testing to ensure that all hydraulic connections are properly and tightly made prior 

to applying pressure. Personnel must wear eye protection to prevent injury. 

Personal Protective Equipment 

Wear eye protection approved for the materials and tools being used. 

Symbols Used in this Manual 

In this manual, a 

Warning

 identifies conditions and actions that pose a hazard to the 

user. A 

Caution

 identifies conditions and actions that may damage the Hydraulic 

Comparison Test Pump. 
Symbols used on the Hydraulic Comparison Test Pump and in this manual are explained 

in 1. 

Содержание P5515





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды