Flowserve WDX E Скачать руководство пользователя страница 12

Страница: 12 / 46

WDX USER INSTRUCTIONS ENGLISH 71576322 06-05

Page 12 of 46

2.4 Storage

Store the pump in a clean, dry location

away from vibration. Leave piping connection covers

in place to keep dirt and other foreign material out of
pump casing. Turn pump at intervals to prevent

brinelling of the bearings and the seal faces, if fitted,
from sticking.

Do not store pumps starting on the fan guard.

The pump may be stored as above for up to 6

months. Consult Flowserve for preservative actions
when a longer storage period is needed.

2.5 Recycling and end of product life

At the end of the service life of the product or its

parts, the relevant materials and parts should be
recycled or disposed of using an environmentally

acceptable method and local regulations.
If the product contains substances which are harmful

to the environment, these should be removed and
disposed of in accordance with current regulations.

This also includes the liquids and or gases in the
"seal system" or other utilities.

Make sure that hazardous substances or toxic

fluid are disposed of safely and that the correct
personal protective equipment is used. The safety

specifications must be in accordance with the current
regulations at all times.

3 PUMP DESCRIPTION

3.1 Configurations

The WDX type pump is a horizontal, multistage,
radial split case, vaned diffuser type centrifugal pump

equipped with a special suction impeller for low
NPSH. It can be used with motor, steam turbine and

gasoline or diesel engine drives.
The WDX pumps are of modular construction with

identical stages being stacked axially to achieve the
desired pressure output. Four high strength external

tie rods connecting the two end casings hold them
together. A variety of optimal features and materials

allow it to fit a wide range of applications such as
boiler feed or reverse osmosis.

Various orientations for the radial suction and
discharge nozzles are allowed every 90° except

towards the bottom.

The WDX can have the following configurations:

WDXR

Horizontal
Radial suc tion
Drive end on discharge side - C W
Thrust bearing on dri ve si de
Radial bearing on suc tion side
2 shaft s eals

WDXC

Horizontal
Radial suc tion
Drive end on suction side - CCW
Thrust bearing on suc tion si de
Radial bearing on disc harge side
2 shaft s eals

WDXE

Horizontal
End s uction
Drive end on discharge side - C W
Thrust bearing on dri ve si de
Sleeve bearing on sucti on si de
1 shaft s eal

WDXS

Horizontal
Radial suc tion
Drive end on discharge side - C W
Thrust bearing on dri ve si de
Sleeve bearing on sucti on si de
1 shaft s eal

Содержание WDX E















































Результаты поиска

Содержание WDX E

Отзывы:

Похожие инструкции для WDX E

Бренды по названию

Популярные бренды

Flowserve WDX E, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание WDX E

Отзывы:

Похожие инструкции для WDX E

Бренды по названию

Популярные бренды