Flowserve WDX E Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 46

background image

WDX USER INSTRUCTIONS ENGLISH 71576322 06-05

Page 33 of 46

®

2. Disconnect external piping such as balancing drum

bleed line, cooling connections or mechanical seal
pipework.

3. Disconnect the coupling halves. If oil-lubricated

couplings are used, drain the oil before unbolting.

4. Remove the coupling half from the pump shaft and
take off the key.

6.8.2 Dismantling antifriction thrust bearing

For all WDX variants

6.8.2.1 Oil lubricated bearings

Dismount the fan cover [8162] by loosening the
screws.

Remove the fan [2450-03] by loosening screw [6570-
01].
Unscrew the four bearing nuts [6572].

Remove the bearing cover [3211].
Straighten tab on bearing lock washer [6541-01] and

unscrew bearing lock nut [3712].
Repeat the operation for the second blockage.

Remove the spacer sleeve [2460-02].

Remove the snap ring [6544-02].
Remove the spacer sleeve [2460-01].

The whole thrust bearing assembly can then be
removed from the shaft.

6.8.2.2 Grease lubricated bearings

Dismount the fan cover [8162] by loosening the

screws.
Remove the fan [2450-03] by loosening screw [6570-

01].
Unscrew the four bearing nuts [6572].

Remove the bearing cover [3211].
Straighten tab on bearing lock washer [6541-01] and

unscrew bearing lock nut [3712].
Repeat the operation for the second blockage.

Remove the spacer sleeve [2460-02].
Remove the snap ring [6544-02].

Remove the spacer sleeve [2460-01].
The whole thrust bearing assembly can then be

removed from the shaft.

«
...
31
32
33
34
35
...
»

Содержание WDX E















































Отзывы:

Нет отзывов

Похожие инструкции для WDX E

Бренд: Danfoss Страницы: 40

Бренд: Nakayama Страницы: 8

Craftsman 390.269451

Бренд: Sears Страницы: 8

Altherma 3 M Series

Бренд: Daikin Страницы: 24

HYDROMATIC SP50

Бренд: Pentair Pool Products Страницы: 12

Бренд: vacuubrand Страницы: 70

Бренд: Calorex Страницы: 28

Бренд: Winston Страницы: 28

NKVE MCE Series

Бренд: DAB Страницы: 72

FlexxPump 250 OLED

Бренд: DLS Страницы: 80

POWER VENTED GAS FIRED WATER HEATER

Бренд: GSW Страницы: 39

Бренд: Wahl Bach Страницы: 12

Бренд: Graco Страницы: 24

Бренд: venotec Страницы: 40

Smart Cylinders MS13555030S

Бренд: Rinnai Страницы: 24

Бренд: A.O. Smith Страницы: 2

Бренд: GEA Страницы: 44

Бренд: salmson Страницы: 336

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды