FlowLine EchoPod DL34 Series Скачать руководство пользователя страница 6

Страница: 6 / 12

QS204215 Rev B

WRITE TO UNIT

This WebCal

* operation uploads the configuration into the sensor, provides a custom wiring diagram specific

to the signal output and/or relay configuration, and saves the configuration file to your hard drive.

* For complete information on the WebCal

software, please refer to the WebCal

manual located at

flowline.com/webcal-software.

Before configuration can be completed:



You must click the

Write to Unit

button to save the settings to the unit.



Then, click

Wiring Diagram

for a hard copy of the sensor’s settings.



Finally, enter the file name under which you wish to save the configuration file and click

Save Config

File

Configuration is now complete

Disconnect the USB

Fob before continuing to the next step: Mounting the EchoPod

Содержание EchoPod DL34 Series













Результаты поиска

Содержание EchoPod DL34 Series

Отзывы:

Похожие инструкции для EchoPod DL34 Series

Бренды по названию

Популярные бренды

FlowLine EchoPod DL34 Series, Быстрый старт

Результаты поиска

Содержание EchoPod DL34 Series

Отзывы:

Похожие инструкции для EchoPod DL34 Series

Бренды по названию

Популярные бренды