FlowLine EchoPod DL14 Series Скачать руководство пользователя страница 4

Страница: 4 / 29

4 of 29

EchoPod

31 MAR 11

MN204210

Rev B

Introduction:

The EchoPod is a general-purpose ultrasonic level switch, controller and transmitter that provides a loop
powered 4-20 mA output and 4 SPST 60 VA relays. The 4-20 mA output can be used to provide the
proportional level of liquid in any tank or vessel.  The 4 relays can be used to control multiple combinations of
pumps, valves and/or alarms.  The signal can be connected to any device that accepts a loop powered 4-20 mA
signal or relay output, such as a PLC, SCADA, DCS, display, controller, etc.

New Features



Simple configuration with WebCal software,

no more target calibration



Adjustable Loop Fail-Safe, Hold Last, Empty, Full, 21 mA, 22 mA



Easy to reverse mA output, 4-20 mA to 20-4 mA



Adjustable start-up condition, Empty, Mid (12 mA), Full, Over range (22 mA)



Increased output filtering

Table of Contents

Introduction ............................................................................................................................4
New Features ............................................................................................................................4
About this manual ......................................................................................................................5
Specifications ............................................................................................................................7
Dimensions

............................................................................................................................7

Getting Started ...........................................................................................................................8

USB® Fob Interface ......................................................................................................8

WebCal ..........................................................................................................................9

Step 1: Configuration .........................................................................................9

Step 2: Tank Levels .........................................................................................17

Step 3: Write to Unit ........................................................................................17

Wiring

..........................................................................................................................18

Wiring EchoPod ...........................................................................................................18

Wire Connections.........................................................................................................18

Installation

..........................................................................................................................20

Mounting Guide ...........................................................................................................20

Fitting Selection ...........................................................................................................21

Tank Adapter ...................................................................................................22

Riser .................................................................................................................22

Flange ...............................................................................................................22

Side Mount Fitting ...........................................................................................23

Stand Pipe ........................................................................................................23

Advanced Feature ....................................................................................................................24
Appendix

..........................................................................................................................26

Updating WebCal Software .........................................................................................26

Updating Transmitter Firmware ..................................................................................26

Factory Defaults ...........................................................................................................27

Troubleshooting ...........................................................................................................29

Содержание EchoPod DL14 Series






























Результаты поиска

Содержание EchoPod DL14 Series

Отзывы:

Похожие инструкции для EchoPod DL14 Series

Бренды по названию

Популярные бренды

FlowLine EchoPod DL14 Series, Руководство пользователя

Результаты поиска

Содержание EchoPod DL14 Series

Отзывы:

Похожие инструкции для EchoPod DL14 Series

Бренды по названию

Популярные бренды