(877) 356-5463 | (p) 330-331-7331 | (f) 330-331-7172 | www.FLO-CORP.com | © 2017 FLO-CORP | REVA 1116
3
(877) 356-5463 | (p) 330-331-7331 | (f) 330-331-7172 | www.FLO-CORP.com | © 2017 FLO-CORP | REVA 1116
4
SPECIFICATION
Specifications are subject to change without notice.
Electrical Specifications
Output Functions
The Tracer 1000 is an active, single
ended, non-isolated, 3 or 4 wire analog
output transmitter.
Analog Output
(Active)
Current output 4-20mA: The span
between the lower range value [4mA]
and the upper range value [20mA]
is equal to 0-100% of the continuous
level measurement reading as a factory
default. Output can be inverted.
Total Load
Resistance
< 500Ω: HART resistor approx. 250Ω
+ load resistance approx. 250Ω if the
current output is connected to a device
with an inner resistance of approx. 250
Ω
,
then there is no additional external HART
resistor necessary. In that case, the
HART modem is connected in parallel to
the current output wires.
Lower Range Value
4.0mA (span 0%)
Upper Range Span
20.0mA (span 100%)
Response Time
0.5s (default), 2s 5s (selectable)
Temperature Drift
Less than .0078 in/ºF change in ambient
temperature
Switch Output
DC Switch, PNP, Active, Max. Load 200
mA Current.
Supply Voltage
12-30VDC (reverse-polarity protected)
Current
Consumption
< 50mA at 24 VDC (no burden)
Start-Up Time
< 6s
Cable Terminals
Screwless, cage clamp terminal block for
stranded and solid wires AWG 22-14.
Measurement Specifications
Accuracy
± 0.12” or 0.03% of measured distance,
whichever is greatest
Repeatability
< .08”
Resolution
< .04”
Probe Type
316 SS Rod: 1/4” Dia. (Coated Rod; 3/8” Dia.)
316 SS Coaxial: 3/8” Dia.
Wire Cable: 1/2” Dia.
Probe Length [L]
316 SS Rod: 2.41” - 120”
316 SS Coaxial: 0” - 120”
Wire Cable: 2.41” - 480”
(Length must be specified when ordering - The reference point
is always the sealing surface of the connection thread - See
dimensional drawings)
Top Dead Band
0” Coaxial Probe
2.41” Rod or Wire Probe
Measuring Range
[M]
Up to 780” depending on probe type
Switching Point [S]
Freely positionable within the measuring
range [M] Hysteresis can be set by
defining seperate upper and lower
thresholds; if those are set at the same
position, the minimum hysteresis of .11”
applies
Application Specifications
Dielectric Constant
[ɛ
r
]
Wire & Cable Probe: Configurable
Coaxial Probe: 0
Conductivity
No restrictions
Density
No restrictions
Standard
Application Temp.
F: -40º to 410º
C: -40 to 150º
Optional
Application Temp.
F: -320º to 500º
C: -195 to 260º
Ambient
Temperature
F: -13º to 176º
C: -25º to 80º
Application
Pressure
-14.50 PSI to 580 PSI
Velocity of Level
Change
< 3.2 fps
Mechanical Specifications
Wetted Materials
1.4404 / 316L and PEEK, PTFE
Enclosure Material
Aluminum alloy EN AC-AISi9Cu3 (DIN EN
1706), Epoxy Spray (~70µm)
Enclosure Rating
Standard: NEMA 6 (IP68)
Explosion Proof Option: ATEX NEMA 7
Cable Glands/Screw
Plugs
1/2” NPT (2) or
Cable Glands (2) or
1/2” NPT (1) & Cable Gland (1) or
M20 x 1.5 (2) or
M20 X 1.5 (1) & Cable Gland (1)
Connection Thread
3/4” NPT (US) or 3/4” G (Metric)
Weight (Less Probe)
1.99 lbs. (903.8 g)
Certification
FM: Class I Groups A,B,C,D
Class II Groups E,F,G; Class III; Type 4X
Class I, Div. I, AEx D IIC; IP66
Class I, Div. I, Ex d II C
