background image

Tools needed for   

full installation:

• power drill/screw gun

• tape measure

• commercial grade jig saw*

• Phillips #2 screwdriver bit

• 3/8” drill bit

• 1/8” drill bit

• pencil

• masking tape

• SAFETY GOGGLES

* STOP!

The installer must possess 

the skill to cut within toler-

ance of the template layout 

line if no factory-cutout is 

made in the table top.  

Do not attempt this 

installation without this 

level of craftsmanship skill.

Only skills of using a screw 

driver and wrench are  

required for installation into a 

factory-made cutout.

WARNING: P

oWeR

 T

ools

 A

Re

 D

ANGeRous

Review the safety procedures supplied by your power tool 

manufacturers for your safety’s sake.  Always use safety glasses 

and wear proper apparel that won’t get caught in moving parts. 

CBT Supply, Inc. will not be held liable for misuse of tools and 

disregard for power tool manufacturers’ safety precautions.

Position FIK workstations 30” between centers

8” table depth on the user side

for dual arm keyboard to retract

2.875 depth on the approach side

26” table depth

overall

FIK | FIH 19

20.62 x 15.312

FIK | FIH 23

25 x 15.312

Notes for easy 

installation

Whenever possible, install the 

flipIT before assembling the desk. 

You will be installing from the top 

and the underside: sawhorses 

are recommended. If the desk is 

assembled, see if the desktop can 

be removed.  Always protect the 

surface of your desktop and work 

safely with power tools.
•  The template guides the 

placement of the cutout 8” 

from the user edge.   

•  If the front edge is contoured 

concave or convex, experi-

ment with a scrap piece to 

allow placement of keyboard 

tray or handle. 

•  When 2 or more flipITs are 

installed side by side, keep a 

30” interval between centers.

•  Other factors may enter 

in: the placement of legs, 

brackets and CPU holders 

may require greater distance 

between centers.

technical support 800-770-7042 

www.smartdesks.com

Содержание FIH-19













Отзывы: