Flex-Pro Norprene A3, Руководство по эксплуатации

Страница: 27 / 39

Page 27
OPERATING
FLOW RANGE
(ml/min)
Please note: Contact #1, Contact #2, and Contact #3 use a similar setup menu structure.
This manual will
show setup for Contact #1 only
.
12.0 Output Setup
Below is menu structure for Output Setup selection.
is similar to Input Setup menu. Outputs were designed to directly communicate to
SCADA systems, alarms, data loggers, backup pumps, pumps to operate in sync,
pumps to operate proportionally, and other external devices. Layout of Output Setup menu
Description of Relay and Contact Closure Output triggers
Selection: Contact activates when:
Pump Run/Stop . . . . . Motor turning (roller assembly is rotating).
Monitor Input . . . . . . . Incoming analog or digital signal is not received.
Use with any signal input mode, i.e. 4-20 mA.
Monitor Output . . . . . . Outgoing analog or digital signal not transmitted.
Monitor Run/Fail . . . . . Motor fails to respond to commands.
Both TFD/FVS . . . . . . Either TFD or FVS system triggers.
FVS . . . . . . . . . . . . . . After the programmed delay time, pulses are not
received by flow sensor.
TFD . . . . . . . . . . . . . . Tube failure is detected by sensors in the head.
Active Mode . . . . . . . . Use to monitor any changes to the run mode
selection.
Remote Control Active Use to monitor the remote/local setting.
Disable . . . . . . . . . . . Output contact is disabled.
- Menu
+ Configuration
+ Input Setup
+ Output Setup
<- Esc
- Output Setup
+ Signal Output
+ Relay Output
+ Contact #1
+ Contact #2
Output - Signal
+ Contact #3
<- Esc
H
idden
Output - Assign Relay
- Output Setup
+ Signal Output Modes
+ Contact #1
+ Contact #2
+ Contact #3
<- Esc
+ Relay Output
- 4-20 mA Output
Signal @ min % Motor:
Input mA Signal
@ Min % Motor speed
- 4-20 mA Output
Minimum % Motor:
Input Min % Motor
for mA Signal Output
- 4-20 mA Output
Signal @ Max % Motor:
Input mA signal
@ Max % Motor Speed
- 4-20 mA Output
Maximum % Motor:
Input Maximum % Motor
for mA Signal output
- Relay Output
Both, TFD/FVS
FVS
4-20mA Mode Active
- Signal Output
4-20 mA Output
Freq. Output
Disable
- Signal Output
4-20 mA Output
Freq. Output
Disable
Done Done
- Freq. Output
Signal @ Min % Motor:
Input Frequency (Hz)
@ Min % Motor Speed
000 0
- Freq. Output
Minimum % Motor:
Input Min % Motor
for Freq. output
00.0 0
- Freq. Output
Signal @ Max % Motor:
Input Frequency (Hz)
@ Max % Motor Speed
000 1
- Freq. Output
Maximum % Motor:
Input Maximum % Motor
for Freq. Output
00.0 1
Monitor Input
Monitor Output
Monitor Run/Fail
Manual Mode Active
- Output Setup
+ Signal Output Modes
+ Relay Output
+ Contact #2
+ Contact #3
<- Esc
+ Contact #1
- Contact Closure #1
Monitor Input
Monitor Output
Monitor Run/Fail
Both, TFD/FVS
Disable
TFD
Hi
dde
n
H
idd
en
H
idd
en
Hidden
Output -
Contact Closure #1
(select one) (select one)
0 00.0
0 4.00
1 00.00
2 0.00
Pump Run/Stop
Frequency Mode Active
Cycle Timer Mode Active
Dispensing Mode Active
Manual Dosing Active
Proportional Dosing Active
0-10 VDC Mode Active
Pulse Mode Active
Disable
FVS
TFD
Pump Run/Stop
4-20mA Mode Active
Manual Mode Active
Frequency Mode Active
Cycle Timer Mode Active
Dispensing Mode Active
Manual Dosing Active
Proportional Dosing Active
0-10 VDC Mode Active
Pulse Mode Active
Remote Control Active Remote Control Active
Done Done
Flex-Pro