background image

 

SET UP  

 
Put on the strings and tune to pitch. 
 

1. TRUSS ROD ADJUSTMENT  

The  adjustable  truss  rod  in  the  neck  of  your  Guitar  has  been  shop  adjusted 
and should not require any change. If the neck should develop a dip or hollow 
spot  over  time  it  can  be  removed  by  tightening  the  truss  rod  adjustment  nut 
that protrudes from the base of the headstock just above the nut. 
A "back bow" or "hog-back" can be removed by loosening the nut. Great care 
should be taken with truss rod adjustments where as little as 1/4 of a turn can 
vastly alter the shape of a neck. A broken truss rod of course means a costly 
replacement. 
 

2. STRING ACTION  

The  string  "action"  refers  to  the  height  of  the  strings  above  the  frets.  If  the 
action is too low, the strings will buzz on the frets. If it is too high the guitar will 
be difficult to play. 
 

3. ACTION AT THE NUT  

Setting the string action that is right for you starts at the string nut. The slots at 
the  string  nut  should  already  be  close  to  perfection  but  you  might  want  to 
make some adjustment. Here’s how to do it!  
Push the sixth string down between second and third fret. The space between 
the  top  of the first fret  and  the  bottom  of the  string  should  be  about  .006” or 
just about the thickness of the paper that these instructions are printed on. If 
the gap is wider than .006” you should deepen the slot with a small needle file 
until it is correct. 

DO NOT FILE TOO DEEP!

 If the slot is too deep you can fill 

the slots with a mixture of white plastic sanding dust and crazy glue and then 
re-shape the slot. Repeat this same procedure for the other five strings. The 
action  at  the  nut  is  either  right  or  wrong;  it  is  not  a  matter  of  personal 
preference.  
Now let’s adjust the height of the strings over the 12th fret. Adjustments to the 
string action are made by raising or lowering the Tune-o-Matic Bridge with the 
thumbwheel  height  adjusters.  Following  is  a  chart  to  assist  you.  This  action 
adjustment  is  a  matter  of  personal  preference.  There  should  be  a  gradual 
increase in height from the first to the sixth string. 
 

String Height at the 12

th 

fret 

 

                                                       First String           Sixth String  
Low Action  

1/32

 

1/16

 

Medium Action  

1/16

 

3/32

 

High Action  

3/32

 

1/8

 

 

 
 
 
 
 

Содержание SPR01












Отзывы: