Flavor Burst CTP 80CBB Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 80

Flavor Burst CTP 80CBB Скачать руководство пользователя страница 64

63

Mounting the 9-Tube / Cable Casing
Assembly

The CTP 80CBB includes a metal cable casing
assembly to house and hold the 9-Tube
Assembly level with the Blending Assembly.
Other cables, such as the ethernet cable, can
also be hidden in this assembly, or the plastic
one as explained in the next section.

The following instructions and illustrations show
a right-side mounting, which is typically the side
with the intake vents on the Taylor 430 model.
However, your freezer may have the intake
vents on the left side; in those cases, install the
casing on the left side. It is recommended to
install the casing holding the 9-Tube Assembly
on the

intake

vent side to prevent heating the

syrup tubes. The Touch Panel cable casing
should be installed on the same side the cable
exits the assembly.

1. The casing assembly contains very power

magnets to attach to the side of the freezer.
Simply place the assembly in line with the
Blending Assembly with the hinged surface
down (holding screw at the top). The curved
ends of the casing should hang over the
front and back of the freezer and the
assembly should be level horizontally.

2. Remove the screw from the top of the

casing assembly.

3. Swing the casing cover outward.

4. Carefully place the 9-Tube Assembly inside

the casing. If the Drive Motor is on the
same side as the tubes, include the motor
cable in the casing. Pull any excess tubes
and cables to the back of the freezer,
allowing enough slack in the front to
comfortably curve around to the Blending
Assembly.

5. Close the casing, taking care not to pinch

any of the lines.

6. Install the screw to secure the casing.

26461

26462

26463

26464

26465

26466

«
...
62
63
64
65
66
...
»

Содержание CTP 80CBB

















































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды