FlameStop VESDA-E VEP-A00-1P Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 112

background image

VESDA-E VEP-A00-P Product Guide

36

www.xtralis.com

Notes:

l

The polarity of the data wires must be maintained throughout the network.

l

In order for the detector to be able to detect ground faults on the VESDAnet wiring, the Ground Reference
Terminal (Figure 4-33) must be connected to the local ground.

A+

A-

B-

Shield

Module 1

Module 2

Module 3

Module 5

Module 4

Shield

B+

A+

A-

B-

Shield

Shield

B+

A+

A-

B-

Shield

Shield

B+

A+

A-

B-

Shield

Shield

B+

A+

A-

B-

Shield

Shield

B+

(VESDA-E VEP)

Figure 4-35: Example closed loop VESDAnet network

The VESDA-E VEP-A00 detector is shipped with the VESDAnet A and B terminals looped. Remove the A
and B links prior to connecting the detector to the VESDAnet. If the detector is not to be networked with other
devices, then do not remove the A and B links.

Shield

A-

A+

Shield

B-

B+

Figure 4-36: Closed loop for standalone detectors with VESDAnet capability

Note:

Refer to the VESDA-E Communications Guide for further information.

«
...
40
41
42
43
44
...
»

Содержание VESDA-E VEP-A00-1P

















































































































Отзывы:

Нет отзывов

Похожие инструкции для VESDA-E VEP-A00-1P

Бренд: Radio Shack Страницы: 12

Бренд: REIZEN Страницы: 7

Бренд: La Crosse Technology Страницы: 20

Бренд: resideo Страницы: 2

Бренд: Magicar Страницы: 61

Бренд: Edwards Signaling Страницы: 6

PRO9276E Pursuit Series

Бренд: Voxx Страницы: 28

Бренд: Prestige Страницы: 8

Бренд: Pandora Страницы: 25

Бренд: Polon-Alfa Страницы: 18

Бренд: ELITA Страницы: 2

Бренд: Masterbuilt Страницы: 28

Pursuit PRO9233Z

Бренд: Voxx Electronics Страницы: 8

CRA54 - Digital Alarm Clock

Бренд: Coby Страницы: 1

Бренд: HumanTechnik Страницы: 15

Бренд: ADE Страницы: 158

Бренд: ADE Страницы: 184

SMD-429 PG2 Series

Бренд: Visonic Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды