manualshive.com logo in svg

Fisher EZ easy-e, Инструкция по эксплуатации, Страница: 25 / 36

Поделиться
Скачать
Fisher EZ easy-e Скачать руководство пользователя страница 25

Instruction Manual

D100401X012

EZ Valve

November 2017

25

Packing Kits (ENVIRO‐SEAL) Retrofit

REPAIR KIT MATERIAL

STEM DIAMETER, mm (INCH)

YOKE BOSS DIAMETER, mm (INCH)

9.5 (3/8)

54 (2‐1/8)

12.7 (1/2)

71 (2‐13/16)

19.1 (3/4)

90 (3‐9/16)

Part Number

Double PTFE (Contains keys 200, 201, 211, 212, 214, 215, 216, 217, and 218)

RPACKXRT012

RPACKXRT022

RPACKXRT032

Graphite ULF (Contains keys 200, 201, 207, 208, 209, 210, 211, 212, 214, and 217)

RPACKXRT262

RPACKXRT272

RPACKXRT282

Duplex (Contains keys 200, 201, 207, 209, 211, 212, 214, 215, 216, and 217)

RPACKXRT212

RPACKXRT222

RPACKXRT232

  WARNING

Use only genuine Fisher replacement parts. Components that are not supplied by Emerson Automation Solutions should
not, under any circumstances, be used in any Fisher valve, because they may void your warranty, might adversely affect the
performance of the valve, and could cause personal injury and property damage.

Содержание EZ easy-e





































Отзывы:

Нет отзывов