manualshive.com logo in svg

Fisher EZ easy-e, Инструкция по эксплуатации, Страница: 12 / 36

Поделиться
Скачать
Fisher EZ easy-e Скачать руководство пользователя страница 12

Instruction Manual

D100401X012

EZ Valve

November 2017

12

Table 3. Recommended Torque for Packing Flange Nuts (Not for Spring‐Loaded Packing)

VALVE STEM DIAMETER

PRESSURE

RATING

GRAPHITE TYPE PACKING

PTFE TYPE

PACKING

Minimum Torque

Maximum Torque

Minimum Torque

Maximum Torque

mm

Inches

N

S

m

Lbf

S

in

N

S

m

Lbf

S

in

N

S

m

Lbf

S

in

N

S

m

Lbf

S

in

9.5

3/8

CL125,

CL150

3

27

5

40

1

13

2

19

CL250
CL300

4

36

6

53

2

17

3

26

CL600

6

49

8

73

3

23

4

35

12.7

1/2

CL125,

CL150

5

44

8

66

2

21

4

31

CL250
CL300

7

59

10

88

3

28

5

42

CL600

9

81

14

122

4

39

7

58

19.1

3/4

CL125,

CL150

11

99

17

149

5

47

8

70

CL250
CL300

15

133

23

199

7

64

11

95

CL600

21

182

31

274

10

87

15

131

Trim Maintenance

  WARNING

Observe the warning at the start of the Maintenance section.

This procedure describes how the valve trim can be completely disassembled. When inspection or repairs are required,
perform only those steps necessary to accomplish the task.

Disassembly

Except where indicated, key numbers referenced in the following steps are found in figure 12.

1.  Remove the actuator and the bonnet according to steps 1 through 6 of the Replacing Packing procedure of the

Maintenance section.

  WARNING

Avoid personal injury or property damage from valve or packing leakage.

Any damage to the gasket sealing surfaces could cause the valve to leak.

The surface finish of the valve stem (key 7) is critical for making a good packing seal. The inside surface of the seat ring
retainer is critical for smooth operation of the valve plug.

The seating surfaces of the valve plug and seat ring (keys 2 and 9) are critical for proper shutoff.

Protect these parts accordingly while disassembling the trim. Gasket selection criteria is provided on page 33 of this
instruction manual.

2.  Packing parts can be removed if desired. Replace these parts as described in the Replacing Packing procedure.

Valves with Plain or Extension Bonnets

Perform the following steps to remove the valve trim.

Содержание EZ easy-e





































Отзывы:

Нет отзывов