Fisher Scientific behr behrotest TRS 300 Скачать руководство пользователя страница 28

Страница: 28 / 30

behr TRS 300

– 28 –

271005

behr TRS 300

– 29 –

271005

What do I do if...?

The behrotest

TRS 300 control unit has an internal fault scanning system. This is capable of detecting

five different error situations. „Error“ will then appear on a red background, together with a Code No.,

on the display. An alarm signal (bleep tones) is also heard. The numbers have the following meanings:

Code Meaning

Remedy

002

The temperature sensor is not

connected or not firmly inserted

Switch the unit off. Connect the temperature sensor of the

digester to the „Temp Probe Pt 100“ socket (Page 7, 2.2).

Ensure firm seating of the diode connector. Secure the

connector using the union nut. Only then switch the unit

on again.

003

Short-circuit in temperature

sensor

The digester must be repaired or replaced. Switch

the digester and the TRS 300 off and inform the behr

after-sales service.

Содержание behr behrotest TRS 300































Результаты поиска

Содержание behr behrotest TRS 300

Отзывы:

Похожие инструкции для behr behrotest TRS 300

Бренды по названию

Популярные бренды

Fisher Scientific behr behrotest TRS 300, Руководство по эксплуатации

Результаты поиска

Содержание behr behrotest TRS 300

Отзывы:

Похожие инструкции для behr behrotest TRS 300

Бренды по названию

Популярные бренды