manualshive.com logo in svg

Fisher & Paykel CLEANSMART WL8O60P, Руководство по установке

Поделиться
Скачать
Fisher & Paykel CLEANSMART WL8O60P Скачать руководство пользователя страница 15

15

CONTROL PANEL

1

To turn your washer on, touch 

 for 2 

seconds. This will activate the display panel. 

KEYLOCK

 will remain activated but let you 

select your wash cycle options and start the 
cycle.

To pause your washer at any time during the 
cycle, touch 

 for 2 seconds, or touch 

 

twice in quick succession.

2

1

Touch   for 2 seconds.

When activated, the light above the   button 
is illuminated.

Time to go

Your CleanSmart™ washer displays approximately how many minutes the cycle has 
remaining, so that you can tell at a glance when your washing will be finished. Once you 
have selected your wash cycle and options, the time the cycle will take to complete will be 
displayed. Please be aware that a number of factors influence the overall cycle time, eg the 
water flow rate, load size and cycle selection, therefore times will vary.

Keylock

Keylock can be used to lock the buttons on your CleanSmart™ washer when not in use. This 
will avoid accidental button pushes from items left on the lid of the washer (eg washing 
baskets) and also from any little fingers.

To turn 

Keylock

 ON or OFF:

If 

Keylock

 is ON:

Содержание CLEANSMART WL8O60P





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды