Fisher & Paykel AeroSmart DE62T27CW1 Скачать руководство пользователя | Manualshive

Страница: 10 / 29

background image

517760C

10

5

SERVICE PROCEDURES

Note: These instructions refer to the removal of the display module only. Refer to Service
Manual 517760B for full servicing instructions.

Note: Prior to carrying out any service procedures ensure that the machine has been
isolated from the power supply.

To remove the display module, follow the procedures as detailed below.

5.1

Removal of Lid

(a)

Open the lid fully, then lift off vertically.

Reassembly
Refit in reverse manner, ensuring that the hinge lugs on the lid are
vertical.

5.2

Removal of Console

(a)

Disconnect the unit from the power supply.

(b)

Remove the lid.

(c)

Remove the two screws at the rear of the console securing the
console to the top deck.

(d)

Tilt the console forward.

Reassembly:
Refit in reverse manner.

5.3

Removal of Display Module

(a) Follow procedures for removal of console (refer to

Section 5.2).

(b)

Disconnect the wiring harness from the sensor module.

(c)

Remove the 4 screws securing the display module to
the console

(d) Remove the display module from the housing by

pivoting the display away from the console.

Reassembly:
Refit in the reverse manner.

Lift

Screws

«
...
8
9
10
11
12
...
»

Содержание AeroSmart DE62T27CW1






























Отзывы:

Нет отзывов

Похожие инструкции для AeroSmart DE62T27CW1

Бренд: Fagor Страницы: 36

Бренд: Fagor Страницы: 4

Бренд: Fagor Страницы: 24

Бренд: T-Fal Страницы: 15

Бренд: Daewoo Страницы: 20

Essentials KDF250

Бренд: Kambrook Страницы: 6

Бренд: Amos Страницы: 8

Бренд: Amos Страницы: 11

Бренд: Cosori Страницы: 23

Бренд: Gorenje Страницы: 56

Бренд: Morris Страницы: 4

Бренд: Matco Tools Страницы: 2

Бренд: Saivod Страницы: 84

Бренд: Verloni Страницы: 11

Бренд: Farouk Страницы: 10

Бренд: Cobra Страницы: 20

Бренд: Cobra Страницы: 38

Бренд: Xiaomi Страницы: 121

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды