manualshive.com logo in svg

Fisher & Paykel AeroSmart DE62T27CW1, Руководство по обслуживанию

Поделиться
Скачать
Fisher & Paykel AeroSmart DE62T27CW1 Скачать руководство пользователя страница 18

517760C 

 

18 

7.5 Showroom 

Mode 

 

 
 
 
Showroom mode will play the introduction and repeat it continuously, until the dryer has been 
isolated from the power supply. 
 
To access the showroom mode follow the steps below. 

1.  Turn the power supply to the dryer on. 
2.  During the introduction sequence on the LCD display (which lasts for approx. 1 minute) 

press and hold the 

START/PAUSE 

button, then press the 

SELECT 

button and hold these 

buttons for at least two seconds. 

To exit, turn off the power supply to the dryer at the wall. 

8 

DIAGNOSTIC MODE – LED MODELS 

8.1 

Entering the Diagnostic Mode 

To enter the Diagnostic Mode, turn the power on at the power point and off at the console. 

1.  Press and hold the 

WRINKLE FREE 

button, then press the 

POWER 

button until the 

machine beeps and all eight LEDs across the top of the machine illuminate.  The dryer is 
now in Diagnostic Mode. 

2. Press 

the 

TIME DRY

 button three times to read the last fault. 

 
The fault code is displayed in the row of eight cycle LEDs using a binary code.  Each LED has a 
value as follows: 
 

 LED 

VALUE 

Regular = 

128 

Heavy = 

64 

Delicate = 

32 

Sheets = 

16 

Air Dry 

= 

8 

Bulky = 

4 

Easy Iron 

= 

2 

Wrinkle Free 

= 

1 

 
The fault code is determined by adding up the value of the illuminated LEDs. 
 
For Example: 
 
 
 

128 

64 

32 

16 8 4 2 1 

 
In this example, the LEDs with value “8” “2” and “1” are on. 
Therefore 8+2+1=11.  Fault code 11 is displayed. 
 
Investigate corrective action in sequence as listed in the fault code summary in Section 6.3. 
To exit the diagnostic mode, press the 

POWER 

button. 

Press and Hold 

START/PAUSE

, then press the 

SELECT

 button 

Содержание AeroSmart DE62T27CW1






























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды