First Degree Fitness Fluid E-316 Скачать руководство пользователя страница 11

Страница: 11 / 32

Mainframe

Lower Mainframe

3 x M10x90mm Bolt

3 x M10 Spring Washers

3 x M10 Washer

Mainframe

Lower Mainframe

M10x65mm Bolt

2 x M10x140mm Bolt

M10 Washer

2 x M10 Curved Washers

REQUIRED E316

REQUIRED VX-2

STEP 3

ATTACH LOWER MAINFRAME TO MAINFRAME AND TANK

a) Place Mainframe

on its back.

b) Install left and right side bolts using:

ASSEMBLY

ALIGN VX-2 CURVED
WASHERS

WITH

CURVE OF THE FRAME
FOR FLAT FIT AND TO
AVOID SCRATCHING
THE PAINT.

CAUTION

DO NOT ATTEMPT TO
STAND E316 OR VX-2
ROWER UNTIL FOOTPLATE
ATTACHED. SEE
FOLLOWING PAGES
FOR DETAILS.

WARNING

E316

VX-2

Place Lower Mainframe

onto Mainframe

, DO NOT insert bolts at this time.

2 x M10x90mm Bolts

, 2 x M10 Washers

and 2 x M10 Spring Washers

M10x90mm Bolt

, M10 Washer

and M10 Spring Washer

Attached Lower Mainframe

to Mainframe

using M10x140mm Bolt

DO NOT tighten.

2 x M10x140mm Bolts

and 2 x M10 Curved Washers

. DO NOT tighten.

M10x65mm Bolt

and M10 Washer

. Tighten ALL bolts.

c) Secure Lower Mainframe to Mainframe by installing the center bolt.

Bolt

Lower Frame

Washer

Spring Washer

Содержание Fluid E-316

































Результаты поиска

Содержание Fluid E-316

Отзывы:

Похожие инструкции для Fluid E-316

Бренды по названию

Популярные бренды

First Degree Fitness Fluid E-316, Руководство пользователя

Результаты поиска

Содержание Fluid E-316

Отзывы:

Похожие инструкции для Fluid E-316

Бренды по названию

Популярные бренды