manualshive.com logo in svg

Firegear Key West KWB30 KWB-L1, Руководство пользователя, Страница: 3 / 36

Поделиться
Скачать
Firegear Key West KWB30 KWB-L1 Скачать руководство пользователя страница 3

Firegear Outdoor KWB30

3

3

TABLE OF CONTENTS

SAFETY LABEL

Copy of Safety Decal .....................................................4

DIMENSIONS

KWB30 Unit Dimensions ...............................................5
KWB60 Unit Dimensions ...............................................6

INSTALLATION

Important Message   ......................................................7
Before You Start ............................................................7
General Safety Information............................................7
Installation  Checklist .....................................................8
Locating Your Outdoor decorative gas appliance ..........8
Outdoor appliance installation summary .......................9
Minimum Clearances to combustibles .........................10
Inner Framing dimensions (required) .......................... 11
Finishing ......................................................................12
Optional fi nishing Trim .................................................12
High Elevation .............................................................13
Gas Line Installation ....................................................13
Pilot Adjustment ...........................................................13
Gas Pipe Pressure Testing ..........................................13
886 S.I.T. Valve Description .........................................13
Aeration Adjustment ....................................................13
KWB60 assembly ........................................................14
KWB30 wall switch and Battery installation .................15
(included with unit).......................................................15
KWB60 wall switch and Battery installation .................16
(included with unit).......................................................16
KWB30/KWB60 Drain Installation (Recommended)....17
KWB30 Wiring Diagram...............................................18

KWB60 Wiring Diagram...............................................18
(KWB60=2 X KWB30 assembled end-to-end) ............18
Fireglass installation on burner....................................19
Optional twig Set Installation .......................................20
Optional glass surround Installation ............................22
Assembly instructions for a steel stud framing 
kit for KWB60...............................................................29

OPERATING INSTRUCTIONS

Operating Instructions .................................................31
Lighting Procedure ......................................................31
Shutdown Procedure ...................................................31
First Fire ......................................................................31
Copy of Lighting Plate Instructions ..............................32

MAINTENANCE

Maintenance Instructions.............................................32
Valve assembly replacement .......................................33

PARTS

Parts ............................................................................34

WARRANTY

Limited Warranty:   ......................................................35

Содержание Key West KWB30 KWB-L1





































Отзывы:

Нет отзывов