Firegear Key West KWB30 KWB-L1 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 36

Firegear Key West KWB30 KWB-L1 Скачать руководство пользователя страница 23

Firegear Outdoor KWB30

23

INSTALLATION

ASSEMBLY INSTRUCTIONS FOR A STEEL STUD

SEE THROUGH FRAMING KIT FOR KWB30

Follow these instructions for the 30" burner;

**Non-combustible fi nishing board not supplied with kit. Board may be purchased at your local hardware/building supply store.

IMPORTANT:

Supplied vents need to be installed into non-combustible fi nishing board, before applying fi nishing materials. Follow guidelines

included with these instructions.

377-908 CONTENTS:

Top / Bottom

(A) x 2

Vertical Supports - Tall

(B) x 8

Vertical Supports - Short (C) x 6

Base

(D) x 1

Short Brace

(E) x 4

Header

(F) x 2

Vents

4

Wafer Screws

80

Tools Required

1 power
drill

+ #2 phillips bit

1 hand
#2 screwdriver
(Phillips)

1 level

1
tape
measure

Vent Location

Vent Location

Vent Location

Vent Location

NOTE:

Four (4) ventilation grills are required for all enclosures.

This is to alleviate moisture and allow for air to circulate. Minimum recommended size 20" sq (508 mm²)

ea

.

See fi nishing details in instruction manual.

NOTE:

If installing a propane unit, the propane tank (if installed) and the pilot hood assembly, must be at opposite ends. Do not install pilot side of

unit over propane tank.

Overall dimensions: 64-1/16" W x 51" H x 19" D
Opening dimensions: 42" W x 20-1/2" H

«
...
21
22
23
24
25
...
»

Содержание Key West KWB30 KWB-L1





































Отзывы:

Нет отзывов