Firegear Key West KWB30 KWB-L1 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 36

Firegear Key West KWB30 KWB-L1 Скачать руководство пользователя страница 28

28

Firegear Outdoor KWB30

INSTALLATION

Follow these instructions to construct a steel stud table for the KWB60 burner;

NOTE:

KWB60 is two KWB30 units assembled end to end.

**Non-combustible fi nishing board not supplied with kit. Board may be purchased at your local hardware/building supply store.

Vent Location

Vent Location

Vent Location

Vent Location

Tools Required

1 power
drill

+ #2 phillips bit

1 hand
#2 screwdriver
(Phillips)

1 level

1
tape
measure

377-910 CONTENTS:

Top / Bottom

(A) x 2

Vertical Supports - Corner

(B) x 4

Vertical Supports - Inner

(C) x 6

Vertical Supports - Outer

(C) x 4

Wafer Screws

80

Vent (377-060)

2 x Upper

Vent (377-061)

2 x Lower

Note:

KWB60 - Four (4) ventilation grills are required for all enclosures.

This is to alleviate moisture and allow for air to circulate. Minimum recommended size 20"sq (508mm²) ea.
* Alternative to installing grills would be to raise the KWB60 frame a minimum of 1" (25mm) to allow air circulation from underneath.

Overall dimensions = 24" W x 24" H x 79" L.

ASSEMBLY INSTRUCTIONS FOR A STEEL STUD

TABLE FRAMING KIT FOR KWB60

«
...
26
27
28
29
30
...
»

Содержание Key West KWB30 KWB-L1





































Отзывы:

Нет отзывов