Firegear FPB-20DBSMT-N Скачать руководство пользователя

Страница: 36 / 38

REV. 2-5-18 Page 36

Round Flat Disc Fire Pits

This fire pit instruction provides an option to mount the TMSI face plate to concrete board.

Use the template above to complete the installation.

The TMSI face plate can be mounted vertically or horizontally. Our suggestion is to attach

the face plate in a horizontal position with the gas valve on the left side. This allows the

control knob text to be orientated in a position to be easily read.

Note:

Mounting plate can

also be installed into a paver control panel (PAVER-CP-TMSI) bracket system.

Using scissors carefully cutout the template and trace it on your concrete board. The

dotted line provides the cutout area to mount face plate. Use a concrete drill bit to drill (4)

3/16” diameter holes. Install the 1¼” screws through the front of the faceplate with the

nuts and washers on the backside. These are all provided in the hardware bag.

CAUTION

: Careful not to over-tighten screws and nuts to ensure the cement board does

not crack or break.

Optional Cutout Template for

TMS Face Plate

Содержание FPB-20DBSMT-N







































Результаты поиска

Содержание FPB-20DBSMT-N

Отзывы:

Похожие инструкции для FPB-20DBSMT-N

Бренды по названию

Популярные бренды

Firegear FPB-20DBSMT-N, Инструкция по установке и эксплуатации

Результаты поиска

Содержание FPB-20DBSMT-N

Отзывы:

Похожие инструкции для FPB-20DBSMT-N

Бренды по названию

Популярные бренды