manualshive.com logo in svg

Fire Chief FC450, Руководство пользователя

Поделиться
Скачать
Fire Chief FC450 Скачать руководство пользователя страница 8

5

 

3.  Assemble the following parts using 6 #10 sheet metal screws.  Both “B” and “C” panels should fit inside of “D” and “A” panel  

 

flanges. Attach “D” (bottom panel) to “B” (side panel with electric) and “C” (side panel).  After the bottom and sides are  

 

 

assembled, attach ”A” (top panel) using 6 #10 sheet metal screws provided.

 

 

4.  Position the assembled filter box on rear of furnace, making it flush with the bottom of the furnace, covering the rear 

 

distribution blower.  Make sure the filter box is tightly pressed to the back of the furnace.  Use 8 #10 self-tapping 

 

screws (included) to firmly attach the filter box to the sides of the furnace.    

Top Panel (A)

Side Panel With Electric (B)

Side Panel (C)

Bottom Panel (D)

#10 Sheet Metal Screw

Twelve Places

Side Panel (C)

Bottom Panel (D)

Side Panel with Electric (B)

#10 Sheet Metal Screw

Top Panel (A)

Side Panel (C)

Bottom Panel (D)

#10 Sheet Metal Screw

Top Panel (A)

Side Panel with Electric (B)

Filter Box

#10 Screw

Filter Box

#10 Screw

Filter Box

#10 Screw

Содержание FC450




























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды