Fire Chief FC450 Скачать руководство пользователя страница 20

Страница: 20 / 27

Wiring

Diagram

Adjusting

the

Thermo-Disc

Your FC450 comes with an adjustable Thermo-Disc that turns the blower on and off automatically. The settings are

preset at the factory to turn the blower on at 125 degrees F and off at 105 degrees F. If needed, the Thermo-Disc temperature can be

changed to allow the blower to turn on or off at a lower or higher temperature.

Note: The adjustment settings on the Thermo-Disc will always be 20 degrees apart for on and off operation. For example, if the setting on

the Thermo-Disc is at the highest temperature 130 degrees F the blower will turn on at 130 and turn off at 110 degrees F.

See illustration below to adjust settings.

Note: Never attempt to make adjustments while a fire is burning in the furnace.

1. Make sure power cord is disconnected from electric outlet. Caution to prevent electrical shock never attempt to adjust Thermo-Disc

with electric connected.

2. Remove cover from 2” X 4” electric junction box on side of furnace.

3. Adjust the dial on the Thermo-Disc clockwise for the blower to turn on and off at a higher temperature.

4. Adjust the dial counter clock wise for a lower temperature.

5. After the adjustment has been made replace cover on electric junction box and plug power cord back into electric outlet.

THERMAL

FAN

CONTROL

SWITCH

BLOWER

MOTOR

WHITE

(L2)

BLACK

(L1)

GREEN

(GRD)

WIRING DIAGRAM

FC 450-SH2400

BLACK

JUNCTION BOX

THERMO SWITCH

BOX

100

120

130

TURN POINTER CLOCKWISE

TO INCREASE FAN CUTOFF

TEMPERATURE

(FACTORY SETTING-125 DEG F)

Содержание FC450




























Результаты поиска

Содержание FC450

Отзывы:

Бренды по названию

Популярные бренды

Fire Chief FC450, Руководство пользователя

Результаты поиска

Содержание FC450

Отзывы:

Бренды по названию

Популярные бренды