FIOR & GENTZ NEURO FLEX MAX Скачать руководство пользователя страница 52

Страница: 52 / 55

09-12-18

52/55

Joint Assembly NEURO FLEX MAX

09-12-18

52/55

Joint Assembly NEURO FLEX MAX

If the sliding washer has been damaged during the assembly of the cover

plate (audible cracking), remove the particles and place a new sliding

washer.

Step 23/29

Check if the bearing nuts are placed completely in the intended openings.

Note: The delivered screws are always matching the system joint. Even if the

screws are not as long as the thread of the bearing nuts, that does not aﬀect

the joint’s load capacity.

Step 24/29

Check if the system joint moves freely. Bring the system joint in extension.

In order to check the ﬂexion, hold the orthosis in a horizontal position and

then let go of the femoral shell. The femoral shell should smoothly fall

downward up to the maximum possible ﬂexion grade. If the system joint

Содержание NEURO FLEX MAX
























































Результаты поиска

Содержание NEURO FLEX MAX

Отзывы:

Похожие инструкции для NEURO FLEX MAX

Бренды по названию

Популярные бренды

FIOR & GENTZ NEURO FLEX MAX, Руководство

Результаты поиска

Содержание NEURO FLEX MAX

Отзывы:

Похожие инструкции для NEURO FLEX MAX

Бренды по названию

Популярные бренды