FIOR & GENTZ NEURO FLEX MAX Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 55

background image

09-12-18

9/55

Joint Assembly NEURO FLEX MAX

09-12-18

9/55

Joint Assembly NEURO FLEX MAX

If the sliding washer has been damaged during the assembly of the cover

plate (audible cracking), remove the particles and place a new sliding

washer.

Step 18/23

Check if the bearing nuts are placed completely in the intended openings.

Note: The delivered screws are always matching the system joint. Even if the

screws are not as long as the thread of the bearing nuts, that does not aﬀect

the system joint’s load capacity.

Step 19/23

Check if the system joint moves freely. Bring the system joint in extension.

In order to check the ﬂexion, hold the orthosis in a horizontal position and

then let go of the femoral shell. The femoral shell should smoothly fall

downward until it has reached the maximum possible ﬂexion grade. If the

«
...
7
8
9
10
11
...
»

Содержание NEURO FLEX MAX
























































Отзывы:

Нет отзывов

Похожие инструкции для NEURO FLEX MAX

Бренд: MedRx Страницы: 14

Бренд: SHONAQUIP Страницы: 17

Бренд: medi Страницы: 22

TGR-R KP-O 3432

Бренд: Timago Страницы: 4

Бренд: NRS Healthcare Страницы: 4

Бренд: UpWalker Страницы: 2

Бренд: Raz Страницы: 21

Бренд: EZee Life Страницы: 8

Бренд: EZee Life Страницы: 17

Бренд: Karma Страницы: 80

Бренд: Drive Страницы: 12

Бренд: Drive Страницы: 12

Бренд: Drive Страницы: 20

Бренд: Days Страницы: 19

Бренд: Easy Travel Страницы: 46

Бренд: Top Hygien Страницы: 6

Бренд: SimplyMed Страницы: 2

Бренд: SimplyMed Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды