FIOR & GENTZ NEURO FLEX MAX Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 55

background image

09-12-18

42/55

Joint Assembly NEURO FLEX MAX

09-12-18

42/55

Joint Assembly NEURO FLEX MAX

Alternative Function 4

limitation. Then, ﬁx the tibial shell and try to move the femoral shell against

it. There should be no movement in the system joint.

Note: Mind the information on the locking pawls in the manual.

Step 26/26

Secure both screws with LOCTITE 243 medium strength and the torque

corresponding to the system width.

Step 1/29

Alternative function 4 is an expansion of alternative function 1. At AF 1, the

locked system joint can be used for locking in diﬀerent ﬂexed positions by

exchanging the locking parts. To do so, exchange the extension stop

«
...
40
41
42
43
44
...
»

Содержание NEURO FLEX MAX
























































Отзывы:

Нет отзывов

Похожие инструкции для NEURO FLEX MAX

Бренд: Afikim Страницы: 30

Bantam PT50001-1

Бренд: EasyStand Страницы: 16

Бренд: aidapt Страницы: 6

Бренд: JusGo Mobiliti Страницы: 2

Бренд: EZee Life Страницы: 2

Бренд: aidapt Страницы: 12

Бренд: Vermeiren Страницы: 236

Бренд: Rehab Страницы: 8

Бренд: identités Страницы: 4

Бренд: Active Страницы: 8

Бренд: Days Страницы: 3

Бренд: Handicare Страницы: 16

REVERGO RH-XL-B

Бренд: Revolution Healthcare Страницы: 5

Quick Release Caster

Бренд: Invacare Страницы: 2

O2 Holder Accessory Kit 1488

Бренд: Invacare Страницы: 1

Бренд: Invacare Страницы: 2

Бренд: Invacare Страницы: 4

Бренд: Invacare Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды