Finn HydroSeeder T75, Руководство по эксплуатации и каталог запасных частей

Страница: 10 / 61

4
MAINTENANCE:
1. Before servicing the
machine, turn off engine
and allow all moving parts
to stop. To prevent acci-
dental starting discon-
nect battery cables. Tag
the engine operating area
to show that the machine
is being serviced. Use
lockout/tagout procedure
(OSHA 29 CFR 1910.147).
2. Certain hydroseeding amendments, when combined
with or without the addition of water or heat or the
element of time, may react causing harmful or deadly
gasses! Consult your material suppliers regard-
ing reactivity information. The slurry tank must be
flushed and drained after each day of operation.
3. Your slurry tank may be
considered a confined
space by OSHA under 29
CFR 1910.146. Before
entering any confined
space, your company must
develop a procedure for
safe entry. Make sure your
company’s plan meets all
the requirements of 29
CFR 1910.146. Including the following:
a) Drain, flush and ventilate tank interior.
b) Turn off engine and disconnect battery cables
and perform lockout/tagout procedures. (29 CFR
1910.147)
c) Provide continuous ventilation or proper breath-
ing apparatus.
d) If tank must be entered, personnel entering the
tank must be tethered to a lifeline.
e) Provide stand-by individual outside of tank able
to communicate with person inside and able to
haul him out with lifeline if necessary.
4. Before loosening any
clamps or opening any
valves, determine if mate-
rial in the line is hot by
feeling the pipe. Do NOT
allow material to come in
contact with personnel.
Severe bodily injury could
result.
5. On trailer units perform general maintenance such
as checking the safety chains, hitch and hitch bolts,
tires, brakes. Repair or replace if worn or broken.
Never operate machine on improperly inflated or
damaged tires. Always use a safety cage or cable
restraints when re-inflating a repaired tire.
6. Radiator maintenance: Liquid cooling systems build
up pressure as the engine gets hot. Before removing
radiator cap, stop the engine and let the system cool.
Remove radiator cap only after the coolant is cool.
7. Battery maintenance: Lead-acid batteries contain
sulfuric acid, which damage eyes of skin on contact.
Always wear a face shield to avoid acid in the eyes. If
acid contacts the eyes, flush immediately with clean
water and get medical attention. Wear rubber gloves
and protective clothing to keep acid off skin. Lead
acid batteries produce flammable and explosive
gasses. Keep arcs, sparks, flames and lighted
tobacco away.
8. Filling of fuel: Never fill the tank with the engine
running, while smoking or when near an open flame.
Never smoke while handling fuel or working on the
fuel system. The fumes in an empty container are
explosive. Never cut or weld on fuel lines, tanks or
containers. Move at least 10 feet (3 meters) away
from fueling point before starting engine. Wipe off
any spilled fuel and let dry before starting engine.
NOTE: Be careful not to allow fuel, lubricant,
hydraulic fluid or cooling fluids to penetrate into
the ground or be discharged into the water system.
Collect all fluids and dispose of them properly.
9. It is recommended that only authorized genuine
FINN replacement parts be used on the machine.
10. Do not use either cold start fluid if engine is
equipped with glow plug type preheater or other
intake manifold type preheater. It could cause an
explosion or fire and severe injury or death.
11. Diesel fuel or hydraulic fluid under pressure can
penetrate the skin or eyes and cause injury, blind-
ness or death. Pressure may build up in the hydraulic
system; use caution when removing the cap.
12. Make certain that all decals on the machine are
maintained in good legible condition. Replacement
decals are available through Finn Corporation by
specifying part number shown in the lower right
hand corner of the decal. See page 5 for the current
safety decals mounted on the unit. See pages 70-71
in the Parts Manual for the location and quantity of
all decals on this unit.