background image

ADJUSTMENT 

AND 

INSPECTION 

MAGNA 65-70-75-83 

Doc. 10004978 

Issued 27/03/2008 

Rev. 00 

P a g .  

2  d i  19 

 

 

 

Menu of the Console 

HEADING: the features of the console and of the chopper card: voltage and maximum current of the 

chopper card, the working hours of the chopper card. 

 

PARAMETER CHANGE: in this menu the parameters can be changed to personalise the machine. The 

parameters that can be modified are : CUT BACK SPEED 1 (minimum speed machine) and the CUT BACK 

SPEED 2 (medium speed machine). All the other parameters are decided in Fimap and they are 

related to the traction motor. It is forbidden to change them without previous Fimap 

authorisation. 

 

TESTER: the quantities of the electric characteristics (traction motor voltage, state of power switch = 

closed/open  ...) are showed in this menu. 

 

SAVE: this permits, once the parameters have been changed, to enter the new setting in a storage 

location of the console.  

 

RESTORE: this permits to restore on the chopper card a parameter setting which has been entered in 

the console.  

 

ALARMS: indicates a list of the last five alarms occurred on the machine. According to the alarm a 

specific corrective action is adopted (see following paragraph). 

 

PROGRAM VACC: this section is used to teach the chopper about the potentiometer which is assembled 

on the machine. It is an operation to be carried when there is the alarm Vacc not ok, when the 

pedal accelerator is being replaced, when the chopper card is being replaced. A wrong relation 

between the potentiometer and the chopper card causes the machine stop. 

 

 
 

Содержание MAGNA 65




















Отзывы: