Fibocom SC806 Скачать руководство пользователя страница 54

Страница: 54 / 70

The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval.

SC806Hardware User ManualPage54 of 70

7.1.3

Bluetooth overview

The SC806 module supports BT4.1 (BR/EDR+BLE) standards. The modulation method supports GFSK, 8-DPSK

and π/4-DQPSK.BR/EDR. Channel bandwidth is 1MHz and can accommodate 79 channels. The BLE channel

bandwidth is 2MHz and can accommodate 40 channels. Its main characteristics are as follows:

➢

BT 4.1 + BR/EDR + BLE

➢

Support for ANT protocol

➢

Support for BT-WLAN coexistence operation, including optional concurrent receive

➢

Up to 3.5 piconets (master, slave, and page scanning)

Table35BT rate and version information

Version

Date Rate

Throughput

Note

BT1.2

1Mb/s

> 80Kbit/s

BT2.0+EDR

2Mb/s

> 80Kbit/s

BT3.0+HS

24Mbps

See3.0+HS

BT4.1 LE

24Mbps

See4.1 LE

The reference standards are as follows:

Bluetooth Radio Frequency TSS and TP Specification 1.2/2.0/2.0 + EDR/2.1/2.1+ EDR/3.0/3.0 +

HS, August 6, 2009

Bluetooth Low Energy RF PHY Test Specification, RF-PHY.TS/4.0.0, December 15, 2009

7.1.4

Bluetooth performance parameters

Table36BT performance parameters

Type

DH-5

2-DH5

3-DH5

Unit

Transmitter

11±1

10±1

dBm

Sensitivity

-93

-90

-86

dBm

Содержание SC806







































































Результаты поиска

Содержание SC806

Отзывы:

Бренды по названию

Популярные бренды

Fibocom SC806, Руководство пользователя по оборудованию

Результаты поиска

Содержание SC806

Отзывы:

Бренды по названию

Популярные бренды